K.C.D. STUDWELDING CD1000 страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 16

background image

CD1000 Pin Welder Instruction Manual

K.C.D. Studwelding, Cheltenham, Victoria. Tel: 03 9584 1588, Fax: 03 9584 1688

6

PIN WELDER GUN

GUN SET UP FOR WELDING PINS

By using a nylon chuck guard, weld pins of various lengths may be used without any

adjustment to the gun head.

NOTE:

The nylon chuck guard must be floating freely on the chuck and must not be tightened onto

the gun shaft. This is because when the pin is forced down onto the work, the chuck guard

forces back onto the chuck, tightening the chuck closed on the weld pin. This produces less

burning on the pin and hence longer chuck life.

«
...
5
6
7
8
9
...
»

Содержание CD1000

















Отзывы:

Нет отзывов

Похожие инструкции для CD1000

Бренд: raumplus Страницы: 23

Бренд: QSC Страницы: 2

Бренд: QSC Страницы: 2

Бренд: QSC Страницы: 16

Бренд: QSC Страницы: 4

Бренд: GBR Systems Страницы: 161

Бренд: KEF Страницы: 24

Бренд: RCF Страницы: 18

Бренд: Vulcan-Hart Страницы: 28

Бренд: PYLE Audio Страницы: 4

Бренд: Sandstrom Страницы: 32

Бренд: Electro-Voice Страницы: 8

Бренд: SANJIANG Страницы: 8

OILPRESS 180.902

Бренд: WILHELM KELLER Страницы: 4

Бренд: Fender Страницы: 6

Бренд: HEEVE Страницы: 8

Бренд: MET Страницы: 4

DRINKWORKS Home Bar Classic

Бренд: Keurig Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды