K-array Kobra KK52 Скачать руководство пользователя

Страница: 48 / 52

KMT12/KMT18

REV. A

Notes for data

1. Maximum RMS applicable power for a musical signal, the reference signal is the one proposed by EIAJ

standard.

2. Measured @4 mt then scaled @1 mt
3. Amplifier wattage rating is based on the maximum unclipped burst sine wave RMS voltage that the

amplifier will produce into the nominal load impedance.

New materials and design are introduced into existing products without previous notice. Present systems

may differ in some respects from those presented in this brochure.

Notes for data

1. Maximum RMS applicable power for a musical signal, the reference signal is the one proposed by EIAJ

standard.

2. Measured @4 mt then scaled @1 mt
3. Amplifier wattage rating is based on the maximum unclipped burst sine wave RMS voltage that the

amplifier will produce into the nominal load impedance.

New materials and design are introduced into existing products without previous notice. Present systems

may differ in some respects from those presented in this brochure.

11. SPECIFICATIONS

Acoustics

Speakers power

handling

700 w

(EAS)

Maximum power

1200 w

Impedance

8Ω

Frequency range

40Hz - 150 Hz +/- 3dB (preset dependent)

SPL 1W/1mt

99 dB

Maximum SPL

128 dB continuous - 134 dB peak

Coverage

Omni

Crossover

Type

DSP controlled

Frequency

150 Hz maximum (preset dependent)

Transducers

1 x 12” Neodymium speakers with 3”

voice coil

Audio Input

Analog

Connectors

2 male + 2 female 3-pin balanced XLR

Digital

Connectors

1 male + 1 female 3-pin XLR

Audio powered Output

Connector

Female Speakon

Wiring

Pin1+= CH1+ Pin1= CH1- Pin2+= N.C.

Pin2= N.C.

Remote control Input

Connectors

1 male + 1 female XLR parallel

1 USB B Jack serial converter

Power Input

Connectors

2 x PowerCon IN/OUT

Amplifiers

Type

1 modules class D - DSP controlled

Subwoofer power

1000 Watt

@8Ω

Speaker power

output

1000 Watt

@8Ω

Protection

Dynamic limiter, over current, over temp,

short circuits

AC power

Operating range

90 - 125 Vac 60Hz / 190 - 240 Vac 50Hz

(Auto Switch)

Consumption

410 W

Minimum

operation voltage

85 Vac - 185 Vac

Maximum

operation voltage

135 Vac - 250 Vac

Max continuos

and

burst current

6A(>10 sec) - 12A (<1 sec) @ 230V

10A(>10 sec) - 20A (<1sec) @ 115V

Physical

Dimensions

32.5 x 33.5 x 43.5 cm

(12.91” x 13.19” x 17.13”)

Weight

15.6 kg (34.39 lbs)

KMT12

Содержание Kobra KK52





















































Результаты поиска

Содержание Kobra KK52

Отзывы:

Похожие инструкции для Kobra KK52

Бренды по названию

Популярные бренды

K-array Kobra KK52, Руководство пользователя

Результаты поиска

Содержание Kobra KK52

Отзывы:

Похожие инструкции для Kobra KK52

Бренды по названию

Популярные бренды