manualshive.com logo in svg

K-array Kobra KK52, Руководство пользователя

Поделиться
Скачать
K-array Kobra KK52 Скачать руководство пользователя страница 35

REV. A

KMT12/KMT18

11

8. AMPLIFIER

8.1  AC POWER CONNECTOR

8.2 VOLTAGE REQUIREMENT

8.3 CURRENT REQUIREMENT

The amplifier module and any audio equipment connected to it (mixing consoles, processors, etc.) must be 

properly connected to the AC power distribution, preserving AC line polarity.  All grounding points should be 
connected to a single node or common point, using the same cable gauge as the neutral and line cables. Bad 
grounding connections within an audio system can produce noise, hum and/or serious damage to the input/
output stages in the system’s electronic equipment.

Before applying AC to any K-array self-powered speaker, be sure that the voltage 
potential difference between neutral and earth ground is less than 5 VAC.

The KMT12 and KMT18’s switching power supply accommodates AC mains operating at either 

115V or 230V. The KMT amplifiers will continue to operate safely, without interruption, provided the 
AC voltage remains within 90 - 135V or 190 - 250V (230V), at 50 or 60 Hz.  Please verify that your 

AC mains connection is capable of satisfying the power ratings for the device.

CAUTION

Do not connect the system to AC power mains exceeding 250V. Doing so will 

cause significant damage to the device and create serious risk for users!

The KMT12 and KMT18 present a dynamic load to the AC mains, drawing additional current as operating 
levels increase. Different cables and circuit breakers heat up at varying rates, so it is essential to understand 

current ratings and how they correspond to circuit breaker and cable specifications. Maximum continuous 

RMS current - measured over a period of at least ten seconds - is used to calculate the temperature increase 

in cables, which drives the proper size and gauge cable and rating for slow-reacting thermal breakers.  Maxi

-

mum burst RMS current - measured over a period of approximately one second - is used to select the rating 

for fast reacting magnetic breakers. 

Содержание Kobra KK52





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды