background image

6

The PXIe-63935 provides the following I/O and indicators, as labeled on the front panel.

•  PXI Trigger Connector (SMB jack)
• 

2X DisplayPort Connectors

•  GPIB Connector (Micro D-Sub 25P)
•  Reset Button
• 

LED indicators

•  4X Type-A USB 2.0
• 

connectors

• 

2X Gigabit Ethernet

•  2X USB 3.0
•  1X COM port (D-sub9 serial)

1�3�1    PXIe Trigger Connector

                                

Trigger

 

Ground

 

Figure 1-3: PXIe Trigger SMB Jack

The PXIe trigger connector is a SMB jack, used to route external trigger signals to or from 

the PXIe backplane. Trigger signals are TTL-compatible and edge sensitive. The PXIe-63935 

provides four trigger routing modes from/to the PXIe trigger connector to synchronize PXIe 

modules, including

• 

From a selected trigger bus line to PXIe trigger connector 

• 

From the PXIe trigger connector to a selected trigger bus line

•  From software trigger to a selected trigger bus line
•  From software trigger to PXIe trigger connector

All trigger modes are programmable by the provided driver. Please refer to Section A: PXIe 

Trigger I/O Function Reference for further information.

1�3�2    DisplayPort Connectors

Supporting monitor connection, with, if connecting to VGA/DVI/ HDMI monitors, installation 

of requisite adapters required. Dual display function is also supported

Содержание PXIe-63935






































Отзывы: