manualshive.com logo in svg

JVC SP-PWC3, Руководство по обслуживанию

Поделиться
Скачать
JVC SP-PWC3 Скачать руководство пользователя страница 12

1-12 (No.MB358)

3.1.8 Removing the main board 

(See Fig. 11)

• Prior to performing the following procedures, remove the metal

cover, rear panel, audio & digital input board and tuner.

(1) From the top side of the main body, remove the screw 

Q

attaching the bracket board and take the bracket board.

(2) Remove the screw 

R

 and screw 

R'

 attaching the main

board on the bottom chassis.

Reference:

When attaching the screw 

R'

, attach the wire protection

board with it.

(3) Take out the wire protection board, and disconnect the

card wires from the connectors (

CN401

 to 

CN403

) on the

main board.

Reference:

When attaching the wire protection board, attach the
wire protection board after connecting the card wires to
the connectors (

CN401

 to 

CN403

) on the main board.

(4) Disconnect the card wires from the connectors (

CN450

 and

CN460

) on the main board.

(5) Disconnect the parallel wires from the connectors (

CN404

to 

CN407

, 

CN456

 and 

CN457

) on the main board.

(6) Take out the main board from the main body.

Fig.11

Main board

R

Q

R'

Bracket
board

CN404

CN407

CN406

Bottom chassis

CN405

CN402

CN401

Wire protection board

CN457

CN460

CN456

CN403

CN450

Содержание SP-PWC3





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды