manualshive.com logo in svg

JVC SP-PWC3, Руководство по обслуживанию

Поделиться
Скачать
JVC SP-PWC3 Скачать руководство пользователя страница 10

1-10 (No.MB358)

3.1.3 Removing the DVD changer mechanism assembly 

(See Fig. 7)

• Prior to performing the following procedures, remove metal

cover and front panel assembly.

(1) From the top side of the main body, remove the screw 

E

 at-

taching the wire protection board to the main board.

(2) Take out the wire protection board, and disconnect the

card wires from the connectors (

CN401

 to 

CN403

) on the

main board.

Reference:

When attaching the wire protection board, attach the
wire protection board after connecting the card wires to
the connectors (

CN401

 to 

CN403

) on the main board.

(3) Remove the four screws 

F

 attaching the DVD changer

mechanism assembly on the bottom chassis.

(4) Take out the DVD changer mechanism assembly in the up-

ward direction.

Reference:

When attaching the DVD changer mechanism assembly, align
the holes of the DVD changer mechanism assembly to the pro-
jections 

d

 on the bottom chassis.

Fig.7

3.1.4 Removing the rear panel 

(See Fig. 8)

• Prior to performing the following procedures, remove the metal

cover.

(1) From the back side of the main body, remove the screw 

G

and eleven screws 

H

 attaching the rear panel.

Fig.8

Main
board

CN402

Bottom
chassis

DVD changer mechanism assembly

Card wires

Wire protection board

F

F

F

Projections 

d

CN401 CN403

E

G

H

Rear panel

H

Содержание SP-PWC3





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды