JVC RV-NB20B, Инструкция по эксплуатации

Страница: 21 / 68

18
„„
Specifications
Amplifier
Output Power
6 W per channel, min. RMS, at 4
Ω
from 150 Hz to 15
kHz with no more than 10% total harmonic distortion.
20 W per channel woofer, min. RMS into 4
Ω
at 60 Hz
with no more than 10% total harmonic distortion.
Input Sensitivity/Impedance (1 kHz)
AUX 300 mV/47 k
Ω
MIC/GUITAR INPUT: Switchable
MIC 200
Ω
– 2 k
Ω
(6.3 mm dia. plug)
GUITAR 100 k
Ω
– 1 M
Ω
(6.3 mm dia. plug)
Output Sensitivity/Impedance (1 kHz)
Phones 16
Ω
– 1 k
Ω
0 – 12 mW/ch output into 32
Ω
Disc Player
Dynamic range 90 dB
Signal-to-noise ratio 95 dB
Wow and Flutter Unmeasurable
Tuner
FM Tuner
Tuning Range 87.5 MHz – 108.0 MHz
AM Tuner
Tuning Range 530 kHz – 1 710 kHz
Antenna FM telescopic antenna
Ferrite core antenna for AM
Speakers
Full range 8 cm (3-3/16")
×
2, 4
Ω
Super woofer 16 cm (6-5/16")
×
2, 4
Ω
General
Dimensions 690 mm
×
239 mm
×
293 mm (W/H/D)
(27-3/16"
×
9-7/16"
×
11-9/16")
Mass 9.2 kg (20.3 lbs) (without batteries)
10.3 kg (22.8 lbs) (with batteries)
Power Specifications
Power Requirements AC 120 V , 60 Hz
DC 15 V (“R20/D(13F)” batteries [10])
External DC 12 V (car battery via
optional CA-R120 car adapter)
Power Supply to iPod 5 V/500 mA
Power Consumption
AC 120 V , 60 Hz 50 W (power on mode)
1.3 W (in standby mode)
External DC 12 V 2.5 A (power on mode)
Symptom Possible cause Action
• The track skips. • The disc is dirty or scratched. • Clean or replace the disc.
• The disc does not play (“NO PLAY” or
“NO DISC” appears).
• The disc is upside down.
• The disc is dirty or scratched. • Put the disc in with the label side up.
• Change the disc.
• Specific files (tracks) on an MP3 disc are
not played.
• Files other than MP3 are included in the
disc.
• They cannot be played.
• iPod is not turned on. • Connection is not firmly made. • Check the connection. (See page 6.)
• iPod does not play though “CONNECT”
appears on the display.
• The battery of the iPod is empty. • Leave the iPod connected for more than
approximately ten minutes.
• iPod is not charged. • FM/AM is selected as the source.
• The system is in a standby mode when
the system is operated on the batteries or
the car battery (DC12V).
• Select any source other than FM/AM.
• Turn on the system.
• Unable to operate the remote control. • The path between the remote control and
the sensor on the system is blocked.
• The batteries have lost their charge.
• Remove the obstruction.
• Replace the batteries.
• Operations are disabled. • The built-in microprocessor has
malfunctioned due to external electrical
interference.
• Unplug the system then plug it back in
after a few minutes.
• Indicators and the display do not light up
while in standby mode.
• Batteries or DC power is used to supply
the power.
Design and specifications are subject to change without notice.
RV-NB20[J].book Page 18 Tuesday, August 22, 2006 3:28 PM