background image

(No.XE003)1-15

5.4

Caution in replacing a bottom case

COA LABEL

 [LE40888-002A/COA LABEL PRO ] can not be reused. When replacing the bottom case, COA LABEL is also needed.

Serial label

Serial labels with model names and serial numbers are not stocked as service parts. Reuse the serial label. Use glue remover when
removing the serial label.
Parts No:UN-001 
Parts name:SUBSIDIARY MATERIAL

Removing the serial label

(1) Drip a few drops of glue remover onto the spatula .
(2) Immediately remove the serial label slowly and carefully with a spatula.
(3) If any stickiness left on the surface of the label, drip few more drops of glue remover and wipe with some tissue paper.    

5.5

Main board replacing procedure

(1) Replace parts from the previous MAIN BOARD.

• Replace [HDD].
• Replace [LAN BOARD ASSY].
• Replace an expansion memory. (If there is any) 

(2) Adjust after the main board replacement.

• Conform the BIOS version to the previous MAIN BOARD.
• If the client wish an update, comply with the client's request.

(3) Perform an operation check after the replacement of the main board.

Perform an operation check according to the [ Operation check item list after the repair is completed ].

5.6

Operation check item list after the repair is completed

Item

Contents

Required equipment

1

IEEE1394

Is the digital video camera recognized, when it is connected to
IEEE1394 port?

JVC digital video camera

2

PC CARD SLOT

Is the PC card which is corresponding to Card Bus recognized,
when it is inserted into PC CARD SLOT?

PC card, that is corresponding to Card Bus,
on the market.(e.g. 100Mbase-T LAN card)

3

USB

Is the mouse recognized, when it is connected to USB?

USB mouse on the market  (Low transfer
rate)

4

MIC

Can the sound be recorded, when a MIC on the market is con-
nected?

MIC on the market

5

HEADPHONE

Can the sound be heard, when a headphone on the market is
connected?

Headphone on the market

6

LAN

Is the network recognized, when it is connected to LAN?

Network

7

WIRELESS LAN

Is the network recognized, when it is connected to WIRELESS
LAN?
Does WIRELESS LAN ON/OFF switch work? 

Network, Access point for WIRELESS LAN

8

MODEM

Can the MODEM be connected to the Internet through the tele-
phone line?

Telephone line. PPP account to connect di-
alup with the Internet.

9

DC in

Can AC be driven?

General power supply 

10

BATTERY

Is the outer battery recognized?
Can battery be driven?
Can it be switched to charge mode?

Outer battery

11

RESET

Is RESET effective?

12

KEYBOARD

Is the key input effective?

13

STICK

Does the STICK work?

14

THREE BOTTON Does each button operate normally?

15

SPEAKER

Is the sound emitted from both channels of the SPEAKER?

16

RUNNING

Is there any trouble when it is continuously played back by Win-
dows Media Player for eight hours?

17

SD CARD SLOT

Is SD card recognized, when it is inserted into SD CARD SLOT?

18

BUILT-IN MIC

Can it record sound?

19

VOLUME

Is the VOLUME controllable?

20

BRIGHTNESS 
CONTROL

Is the BRIGHTNESS controllable?

21

DOCKING 
BOARD

Do both USB terminal and VGA terminal function, 
when a port replicator MP-DPX1is connected?

22

ODD

Can it be opened and closed?
Can playback be done with the play button on the TOP CASE?

23

FAN

Is there any abnormal noise or operation?

Содержание MP-XV841DE

















Отзывы: