JVC LT-26C50 Скачать руководство пользователя страница 50

Страница: 50 / 58

Additional preparation

ENGLISH

LT-32/26C50BU/SU / LCT1700-001A-U / English

Connecting speakers/amplifier

While referring to the audio equipment

connection diagram, connect the audio
equipment you want to the TV.
You can use external front speakers to listen

to the TV sound instead of the TV speakers.

Before connecting anything:

• Read the manuals provided with the

amplifier and speakers.

• Turn the TV and amplifier off.
• Note that connecting cables are not

supplied.

• The output from the AUDIO OUT

terminal is not interrupted by headphone
connection to the TV. You cannot cut the
sound from the front speaker even if you

connect a headphone to the TV.

• Adjust the volume of the external

speakers with the amplifier.

without terminal covers

Amplifier

External speakers (Magnetic-shielded type)

LT-32&26C50BUSU_Eng.book Page 49 Wednesday, July 28, 2004 2:20 PM

Содержание LT-26C50



























































Результаты поиска

Содержание LT-26C50

Отзывы:

Похожие инструкции для LT-26C50

Бренды по названию

Популярные бренды

JVC LT-26C50, Инструкция по эксплуатации

Результаты поиска

Содержание LT-26C50

Отзывы:

Похожие инструкции для LT-26C50

Бренды по названию

Популярные бренды