JVC LT-26C50 Скачать руководство пользователя страница 2

Страница: 2 / 58

ENGLISH

LT-32/26C50BU/SU / LCT1700-001A-U / English

Thank you for buying this JVC LCD flat television.

To make sure you understand how to use your new TV, please read this manual thoroughly before you
begin. (“LCD” stands for Liquid Crystal Display.)

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

WARNING

• Fingers may be trapped under the TV causing injuries.

Hold the TV at the bottom in the middle, and do not

allow it to tilt up or down.

WARNING

• The TV may fall causing injuries. Hold the bottom of the

stand with your hand and tilt the TV up and down.

• Do not allow children to hang from the TV, place their

elbows on the TV or lean against the TV. Doing so may
cause the TV to fall over and lead to injuries.

CAUTION

• The TV screen may be damaged if the TV is carried as

shown in the diagram below.

The TV should always be carried by two people.

LT-32&26C50BUSU_Eng.book Page 1 Wednesday, July 28, 2004 2:20 PM

Содержание LT-26C50



























































Результаты поиска

Содержание LT-26C50

Отзывы:

Похожие инструкции для LT-26C50

Бренды по названию

Популярные бренды

JVC LT-26C50, Инструкция по эксплуатации

Результаты поиска

Содержание LT-26C50

Отзывы:

Похожие инструкции для LT-26C50

Бренды по названию

Популярные бренды