FEATURES FOR RECORDING
38
EN
MasterPage: Left
Makes dark subjects or areas even brighter than
they would be under good natural lighting.
Although the recorded image is not grainy, it may
look as if it is strobing due to the slow shutter
speed.
1
Set the Power Switch to “
M
”.
2
Press
NIGHT
so that the Night-Scope
indicator “
” appears.
●
The shutter speed is automatically adjusted to
provide up to 25 times sensitivity.
●
“
” appears beside “
” while the shutter speed
is being automatically adjusted.
To deactivate Night-Scope
Press
NIGHT
again so that the Night-Scope
indicator disappears.
NOTES:
●
During Night-Scope, the following functions or
settings cannot be activated and its indicator
blinks or goes out:
•
Some modes of “Program AE With Special
Effects” (
墌
pg. 42).
•
“GAIN UP” in CAMERA Menu (
墌
pg. 32).
•
“DIS” in MANUAL Menu (
墌
pg. 32).
●
During Night-Scope, it may be difficult to bring the
camcorder into focus. To prevent this, use of a
tripod is recommended.
This feature lets you record still images that look
like photographs onto a tape.
1
Set the
VIDEO/MEMORY
Switch to “VIDEO”.
2
Set the Power Switch to “
M
”.
3
Set “SNAP/SLOW” to the desired mode.
(
墌
pg. 31, 32) The Snapshot indicator “
”
appears.
4
Press
SNAPSHOT
.
●
There is the sound effect of a shutter closing.
●
The “
O
” indication appears and a still image
will be recorded for approx. 6 seconds, then the
camcorder re-enters the Record-Standby mode.
●
You can perform Snapshot also during recording.
A still image will be recorded for approx.
6 seconds, then the normal recording resumes.
●
Regardless of the Power Switch position (“
A
” or
“
M
”), Snapshot recording takes place using the
selected Snapshot mode.
Motor Drive Mode
Keeping
SNAPSHOT
pressed in step
4
provides
an effect similar to serial photography. (Interval
between still images: approx. 1 second)
●
The Motor Drive mode is disabled when “REC
SELECT” is set to “
/
”. (
墌
pg. 35)
The camcorder’s Full Range AF system offers
continuous shooting ability from close-up (as
close as approx. 5 cm to the subject) to infinity.
However, correct focus may not be obtained
depending on the shooting condition. In this
case, use the manual focus mode.
1
Set the Power Switch to
“
M
”.
2
Press
FOCUS
. The
manual focus indicator
appears.
3
Press
+
or
–
to focus on
a subject.
●
When the focus level
cannot be adjusted any
further or closer, “
” or “
” will blink.
4
Press
MENU
. Focus adjustment is complete.
To reset to Auto Focus
Press
FOCUS
twice or set the Power Switch to
“
A
”.
Manual focus is recommended in situations
listed below.
●
When two subjects overlap in the same scene.
●
When illumination is low.*
●
When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-
colour wall, or a clear, blue sky.*
●
When a dark object is barely visible in the LCD
monitor or the viewfinder.*
●
When the scene contains minute patterns or
identical patterns that are regularly repeated.
●
When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
●
When shooting a scene with a high-contrast
background.
* The following low-contrast warnings appear
blinking: , ,
and .
Night-Scope
Snapshot (For Video Recording)
Manual Focus
Manual focus
indicator
GR-D290_270Asia_07Advanced.fm Page 38 Friday, March 18, 2005 3:34 PM
