JVC DT-V20L1, Инструкция по эксплуатации

Страница: 9 / 20

9
7
Available signals
The following signals are available for this monitor.
Video signals
No. Signal name
Input terminal
VIDEO
(INPUT1, INPUT2)
COMPO./RGB
(Analog component/
analog RGB)
HD/SD SDI (IN 1, IN 2) * 1
(DT-V24L1D and
DT-V20L1D only)
DVI-D (HDCP)
(Digital component/digital
RGB)
1 NTSC √ — — —
2 PAL √ — — —
3 SECAM √ — — —
4 BW(50Hz/60Hz) √ — — —
5 480/60i — √ √ —
6 576/50i — √ √ —
7 480/60p — √ — √
8 576/50p — √ — √
9 640
∗
480/60p — — —
√
10 720/60p — √ √ √
11 720/50p — √ √ √
12 720/30p — √ √ —
13 720/25p — √ √ —
14 720/24p — √ √ —
15 1080/60i — √ √ √
16 1035/60i — √ * 2 √ —
17 1080/50i — √ √ √
18 1080/60p — — — √
19 1080/50p — — —
√
20 1080/30p — √ √ √
21 1080/25p — √ √ √
22 1080/24p — √ √ √
23 1080/30psF — √ *
3
√ *
3
—
24 1080/24psF — √ √ —
√ : Acceptable
— :
Not acceptable
* 1 Compatible with EMBEDDED AUDIO
* 2 Displays the picture as 1080/60i, and “1080/60i” is displayed in the status display ( ☞ page 7).
*
3
“1080/60i” is displayed in the status display (
☞
page 7).
Computer signals (preset)
DVI-D (HDCP) terminals
No. Signal name
Screen resolution
Horizontal
frequency (kHz)
Vertical
frequency (Hz)
Scan system
Horizontal Vertical
1 VGA60 640 480 31.5 59.9 Non-interlace
2 WVGA60 852 480 31.5 59.9 Non-interlace
3 SVGA60 800 600 37.9 60.3 Non-interlace
4 XGA60 1024 768 48.4 60.0 Non-interlace
5 WXGA (1280) 1280 768 47.8 60.0 Non-interlace
6 SXGA60 1280 1024 64.0 60.0 Non-interlace
7 WSXGA+60 1680 1050 65.2 60.0 Non-interlace
8 UXGA60 *
4
1600 1200 75.0 60.0 Non-interlace
9 WUXGA60 *
4
1920 1200 74.0 59.9 Non-interlace
10 720/60p 1280 720 45.0 59.9/60.0 Non-interlace
11 1080/60p * 4 1920 1080 67.5 59.9/60.0 Non-interlace
*
4
For DT-V20L1D and DT-V20L1: When No. 8, 9 or 11 signal is input, thin lines will become obscured because their signal
resolution is higher than the screen resolution.
Specification of DVI-D (HDCP) terminal
Connect it to DVI-D output terminal on a personal computer.
Note for analog component/analog RGB signals
The monitor is compatible with G on sync, Y on sync and composite sync (Cs) signals. The monitor is not
compatible with separate sync (HS/VS) signals.
Note for computer signals
• Non-preset signals may not be displayed normally even if its frequency is within the acceptable range.
• When a preset signal is input, the signal format is displayed on the screen. For other signals, the resolution is
displayed.
Note for connections
• Before making any connections, turn off all the equipment.
• Use a cord whose plugs correctly match the terminals on this monitor and the equipment.
• Plugs should be firmly inserted; poor connections could cause noise.
• When unplugging a cord, be sure to grasp its plug and pull it out.
• DO NOT connect the power cord until all connections are completed.
• Refer also to the user manual of each piece of equipment.
Pin
No.
Input signal
Pin
No.
Input signal
Pin
No.
Input signal
1 T.M.D.S Data 2– 9 T.M.D.S Data 1– 17 T.M.D.S Data 0–
2 T.M.D.S Data 2+ 10 T.M.D.S Data 1+ 18 T.M.D.S Data 0+
3 T.M.D.S Data 2 shield 11 T.M.D.S Data 1 shield 19 T.M.D.S Data 0 shield
4 NC 12 NC 20 NC
5 NC 13 NC 21 NC
6 DDC Clock 14 +5 V Power 22 T.M.D.S Clock shield
7 DDC Data 15 GND 23 T.M.D.S Clock+
8 NC 16 Hot Plug Detect 24 T.M.D.S Clock–
DT-V2420L1D_UA_R.indd 9 DT-V2420L1D_UA_R.indd 9 06.11.17 10:40:17 AM 06.11.17 10:40:17 AM