background image

2

Safety Precautions

WARNING: 

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO 
RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE 
PLACED ON THE APPARATUS.

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure 
your personal safety. But 

IMPROPER USE CAN RESULT IN POTENTIAL ELECTRIC SHOCK OR FIRE.

 In order 

not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, 
use, and service. Please read these “IMPORTANT SAFEGUARDS” carefully before use.
•  All the safety and operating instructions should be read before the product is operated.
•  The safety and operating instructions should be retained for future reference.
•  All warnings on the product and in the operating instructions should be adhered to.
•  All operating instructions should be followed.

POWER CONNECTION

The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada) and AC 220 – 240 V (For 
European countries, Asian countries, and United Kingdom).
The power cord attached conforms to the following power supply voltage and countries. Use only the power 
cord designated to ensure safety and EMC regulations of each countries.

This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact 
your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.

•  This product should be operated only with the type of power source indicated on the label. If you are not sure 

of the type of power supply of your home, consult your product dealer or local electric power company.

Warning:

•  Do not use the same power cord for AC 120 V as for AC 220 – 240 V. Doing so may cause malfunction, 

electric shock or fire.

Note for United Kingdom power cord only

The plug of United Kingdom power cord has a built-in fuse. When replacing the fuse, be sure to use only a 
correctly rated approved type, re-fit the fuse cover. (Consult your dealer or qualified personnel.)

How to replace the fuse

Open the fuse compartment with the blade screwdriver, and replace the fuse.

Fuse

For United Kingdom: AC 220 – 240 V

For European and Asian countries: 
AC 220 – 240 V

For U.S.A. and Canada: AC 120 V

Under the following conditions,
1.  Turn off the power.
2.  Unplug this product from the wall outlet.
3.  Refer service to qualified service personnel.

a)  When the product emits smoke or unusual 

smell.

b)  When the product exhibits a distinct change 

in performance —for example, no picture or no 
sound.

c)  If liquid has been spilled, or objects have fallen 

on the product.

d)  If the product has been exposed to rain or 

water.

e)  If the product has been dropped or damaged in 

any way.

f)  When the power supply cord or plug is 

damaged.

•  Do not install this product in the following places:
  – in a damp or dusty room
  – where the product is exposed to soot or steam, such as near the cooking counter or a humidifier 
  – near heat sources
  – where condensation easily occurs, such as near the window
•  Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury to 

a child or adult, and serious damage to the product.

  The product should be mounted according to the manufacturer’s instructions, and should use a mount 

recommended by the manufacturer.

•  Do not use this product near water.
•  Be sure to install the product in the place where proper temperature and humidity are kept (

 “Operating 

conditions” on page 17).

  This product becomes hot during its use. Take enough care when handling the product.

•  Make enough room for inserting or removing the 

power plug. Place the product as close to an AC 
outlet as possible. The main power supply for the 
product is controlled by inserting or removing the 
power plug.

•  When you install the product in a place where 

you cannot easily insert or remove the power plug 
from an AC outlet, do not use the provided power 
cord holder, and insert or remove the power cord 
from the AC inlet on the product.

•  When the product is left unattended and unused 

for a long period of time, unplug it from the wall 
outlet and disconnect the cable system.

•  Do not overload wall outlets, extension cords, or 

convenience receptacles on other equipment as 
this can result in a risk of fire or electric shock.

•  Use only the accessory cord designed for this 

product to prevent shock.

FCC NOTICE
CAUTION:

 Changes or modifications not approved by JVC could void the user’s authority to operate the 

equipment.

NOTE:

 This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference when the equipment is operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in 
a residential area is likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense.

•  Slots and openings in the cabinet are provided 

for ventilation. These ensure reliable operation of 
the product and protect it from overheating. These 
openings must not be blocked or covered.

•  Never push objects of any kind into this product 

through openings as they may touch dangerous 
voltage points or short-circuit the parts, which 
could result in a fire or electric shock.

•  Never spill liquid of any kind on the product.
•  Do not put heavy objects on the product.
•  Do not step on or hang on the product.

Do not use the product for a long time if the sound 
is distorted. 

Do not attempt to service this product yourself, as 
opening or removing covers may expose you to 
dangerous voltages and other hazards. Refer all 
service to qualified service personnel.

U.S.A. only

DT-V2420L1D_UA_R.indd   2

DT-V2420L1D_UA_R.indd   2

06.11.17   10:40:10 AM

06.11.17   10:40:10 AM

Содержание DT-V20L1





















Отзывы: