24
Playing a T
Playing a T
ape
ape
1. Press VCR to control the VCR deck.
2. Insert a pre-recorded video cassette.
•
If the unit is powered off, it will power on
automatically when the tape is loaded.
•
If the Timer indicator lights on the front panel
display window, press STANDBY/ON once.
3. Press PLAY (
N
) to start playback.
•
If a tape without a safety tab is inserted the
unit starts playback automatically.
4. Press STOP
(
x
)
to stop playback.
•
If the tape reaches the end before you press
STOP
(
x
)
the Recorder automatically stops,
rewinds and ejects the tape.
Note:
S-VHS Quasi Playback (SQPB)
•
This Recorder can play back S-VHS recorded
tapes, however, it cannot make recordings using
S-VHS format tapes.
•
SQPB is an abbreviation for S-VHS Quasi
Playback.
Playing a DVD
Playing a DVD
1. Press DVD to control the DVD deck.
2. Press EJECT, OPEN/CLOSE (
Z
) to open the disc
tray. Load your chosen disc in the tray, with the
playback side down.
3. Press EJECT, OPEN/CLOSE (
Z
) to close the
tray. Playback starts automatically. If playback
does not start, press PLAY (
N
) or Starts play-
back using HOME menu.
4. To stop the playback, press STOP (
x
).
The unit records the stopped point, depending on
the disc. “
Xx
” appears on the screen briefly.
Press PLAY (
N
) to resume playback (from the
scene point). If you press STOP (
x
) again or
unload the disc (“
x
” appears on the screen.), the
unit will clear the stopped point.
5. Press EJECT, OPEN/CLOSE (
Z
) to remove the
disc.
Press EJECT, OPEN/CLOSE (
Z
) to close disc
tray or press STANDBY/ON (
1/&
), the disc tray
closes automatically and unit turns off.
Playback
Remote Control Function
(Refer to page 7)
Remote Control A/B/C/D Code Switching
The remote control is capable of controlling four JVC
video units independently. Each of the units can
respond to one of four codes (A, B, C or D). The
remote control is preset to send C code signals
because your unit is initially set to respond to C code
signals. You can easily modify your unit to respond
to A, B or D code signals.
1. Press STANDBY/ON (
1/&
) on the unit to turn off
the unit with no video tape inserted.
2. Press the number key “1” for A, “2” for B, “3” for C
or “4” for D
while
pressing ENTER ( ) down on
the remote control.
3. Press
N/``
on the unit for over 5 seconds while
the unit is turned off. The current code appears on
the display window.
4. Press STOP (
x
) on the remote control, the cur-
rent code on the display window changes to new
code and blinks for approximately 10 seconds.
5. The new code setup on unit and remote is done.
Note:
If you change the batteries of the Remote Control
with A, B or D code, the remote control code is set to
C automatically. In this case, you should reset the
remote control code described above.
STANDBY/ON (
1/&
)
Number 1-4
STOP (
x
)
ENTER (
)
B/``
Содержание DR MV79B - DVDr/ VCR Combo
