background image

20

To deactivate the timer temporarily,

Press TIMER on the unit repeatedly until the   (timer)
indicator goes off.

To change the Daily Timer to use,

Press TIMER on the unit repeatedly until the timer number
indicator you want begins to flash.
The timer is activated after a few seconds and the selected
timer number remains lit.
• To change the timer setting, repeat steps 

1

 to 

7

 on page 19.

If the unit is already turned on when the timer on-time
comes

The timer does not work.

When you unplug the AC power cord or if a power
failure occurs

The timer setting remains. Set the built-in clock and activate the
timer again.

Using the Sleep Timer

With the Sleep Timer, you can fall asleep to your favorite
music or radio program.
• You can set the Sleep Timer only when the unit is turned

on.

How the Sleep Timer actually works

The unit automatically turns off after the specified length of
time passes.

On the remote control ONLY:

1

Press SLEEP.

The 

SLEEP

 indicator flashes on the display.

• Each time you press the button, the length of time

changes as follows:

2

Wait for about 5 seconds after specifying the
length of time.

The 

SLEEP

 indicator remains lit on the display.

To check the remaining time until shut-off time,

 press

SLEEP once. The remaining time until shut-off time appeears
for about 5 seconds.

To change the shut-off time,

 press SLEEP repeatedly until

the length of time you want appears.

To cancel the setting,

 press SLEEP repeatedly until the

SLEEP

 indicator goes off and display returns to the normal

indication.
• Turning off the unit also cancels the Sleep Timer.

When you set the Sleep Timer after the Daily Timer
starts playing the selected source

The unit follows the Sleep Timer setting.

If you set the Sleep Timer while playing back or
recording a tape

Do not shut the unit off with the Sleep Timer while a tape is running.
If the unit turns off while playing back or recording a tape, the
cassette deck or tapes may be damaged.

SLEEP

SLEEP

10

20

120

30

60

90

Normal indication

(canceled)

Using the Timers 

(continued)

19-20_FS-G2[J]F.p65

04.11.5, 7:13 AM

20

Содержание CA-FSG2

























































Отзывы: