background image

G-1

Warnings, Cautions and Others

  CAUTION:         TO REDUCE THE RISK OF ELECTRIC SHOCK.
                         DO NOT REMOVE COVER (OR BACK)
                      NO USER SERVICEABLE PARTS INSIDE.
  REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, 
within an equilateral triangle is intended to 
alert the user to the presence of uninsulated 
“dangerous voltage” within the product's 
enclosure that may be of sufficient 
magnitude to constitute a risk of electric 
shock to persons.

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.

CAUTION

WARNING: TO REDUCE THE RISK OF FIRE 
OR ELECTRIC SHOCK, DO NOT EXPOSE 
THIS APPLIANCE TO RAIN OR MOISTURE.

For U.S.A.

This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the 
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that 
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION—

 STANDBY/ON button!

Disconnect the mains plug to shut the power off completely (all
lamps and indications go off). The 

 STANDBY/ON button in

any position does not disconnect the mains line.
• When the unit is on standby, the STANDBY lamp lights red.
• When the unit is turned on, the STANDBY lamp goes off.

The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:
1.

Do not remove screws, covers or cabinet.

2.

Do not expose this appliance to rain or moisture.

For Canada/pour le Canada

CAUTION:

 TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

 POUR EVITER LES CHOCS

ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE
DE LA FICHE DANS LA BORNE CORRESPONDANTE DE
LA PRISE ET POUSSER JUSQUAU FOND.

For Canada/pour le Canada

THIS DIGITAL APPARATUS DOES NOT EXCEED THE
CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM
DIGITAL APPARATUS AS SET OUT IN THE INTERFER-
ENCE-CAUSING EQUIPMENT STANDARD ENTITLED
“DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT
OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES
DE BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMERIQUES DE CLASSE B PRESCRITES
DANS LA NORME SUR LE MATERIEL BROUILLEUR:
“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE
MINISTRE DES COMMUNICATIONS.

Front view

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:

No obstructions and open spacing.

2 Sides/ Top/ Back:

No obstructions should be placed in the areas shown by the dimensions below.

3 Bottom:

Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

Side view

FS-G2

FS-G2

10 cm

15 cm

1 cm

15 cm

15 cm

1 cm

15 cm

15 cm

CLASS 1 LASER PRODUCT

DANGER

1.

Invisible laser radiation when open and interlock failed or
defeated. Avoid direct exposure to beam.

CAUTION

1.

Do not open the top cover. There are no user serviceable
parts inside the unit; leave all servicing to qualified service
personnel.

2.

Use of controls, adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.

FS-G2[J]safetyF.p65

04.11.5, 7:12 AM

1

Содержание CA-FSG2

























































Отзывы: