background image

Rev C

 

Page 4 

JA33-001 Bluetooth

®

 Transceiver 

SECTION 2 – INSTALLATION 

2.1 

Introduction 

This section contains unpacking and inspection procedures, installation information, and post-installation checks. 

2.2 

Continued Airworthiness 

Maintenance of the JA33-001 is on condition only. Scheduled inspection and/or periodic maintenance of this unit is 

not required. 

2.3 

Unpacking and Inspecting Equipment 

Unpack the equipment carefully. Check for shipping damage and report any problems to the relevant carrier. Confirm 

that the Authorized Release Certificate or Certificate of Conformance is included. Complete the on-line warranty card 

from the Jupiter Avionics Corporation (JAC) website – 

www.jupiteravionics.com

2.3.1 

Warranty 

Products manufactured by JAC are warranted to be free of defects in workmanship or performance for 2 years from 

the date of installation by an approved JAC dealer or agency. This warranty covers the cost of all materials and labour 

to repair or replace the unit, but does not include the cost of transporting the defective unit to and from JAC or its 

designated warranty repair centre, or of removing and replacing the defective unit in the aircraft. This warranty does 

not cover failures due to abuse, misuse, accident, or unauthorized alteration or repairs. 

THIS WARRANTY IS VOID IF THE PRODUCT IS NOT INSTALLED BY AN AUTHORIZED JAC DEALER. If the on-

line warranty card is not completed, the product will be warranted from the date of manufacture. 

Contact JAC for return authorization, and for any questions regarding this warranty and how it applies to your unit(s). 

JAC is the final arbiter concerning warranty issues.   

2.4 

Installation Procedures 

WARNING

: Loud noise can cause hearing damage. Set the headset volume to minimum before 

conducting tests, and slowly increase the volume to a comfortable listening level. 

CAUTION

The power input circuitry of the unit may be damaged if the installation does not conform to the 

wiring instructions in this manual.

 

2.4.1 

Installation Limitations 

The JA33-001 may be installed only by following the applicable airworthiness requirements. 

2.4.2 

Cabling and Wiring 

All wire shall be selected in accordance with the original aircraft manufacturer’s maintenance instructions, or AC43.13-

1B Change 1, Paragraphs 11-76 through 11-78. Unshielded wire types shall qualify to MIL-W-22759 as specified in 

AC43.13-1B Change 1, Paragraphs 11-85, 11-86, and listed in Table 11-11. For shielded wire applications, use Tefzel 

MIL-C-27500 shielded wire with tag ring or equivalent (for shield terminations) to make the most compact and easily 

terminated interconnect. Follow the Connector Map i

Appendix A

 of this manual. 

 

Содержание JA33-001




























Отзывы: