background image

Assigning additional physical addresses 

Additional physical addresses can be assigned manually with ETS or automatically by the 
device itself. 

Press the programming button (9) for approx. 5 seconds. 
The programming LED flashes. 
The device checks the physical addresses present in the line and selects the required free 
physical addresses. 

Determine the physical addresses occupied by the device and insert them in the ETS 
project as dummy devices. 

When additional bus devices are added, the corresponding physical addresses can be 
assigned twice. Delete the additional physical addresses – press the programming button 
(9) for approx. 10 seconds – and assign them again.  

5 Appendix 

5.1 Technical data 

Power over Ethernet supply 
Power over Ethernet 

IEEE802.3af 

Rated voltage 

DC 48 V 

Power consumption 

max. 0.8 W 

External supply 
Rated voltage 

AC 12 ... 24 V SELV 

Rated voltage 

DC 12 ... 30 V SELV 

Power consumption 

max. 1.7 W 

Connection of power supply 

Connection terminal 

Ambient conditions 
Ambient temperature 

-5 ... +45 °C 

Storage/transport temperature 

-25 ... +70 °C 

Safety class 

III 

Relative humidity 

5 ... 93 % (No moisture condensation) 

Fitting width 

36 mm / 2 modules 

Weight 

approx. 100 g 

Network communication 
IP communication 

Ethernet 10BaseT 

IP transmission rate 

10 Mbit/s 

IP connection mode 

RJ45 socket 

Protocols 

ARP, ICMP, IGMP, UDP/IP, DHCP 

KNXnet/IP 

Core, Routing, Tunneling, Device Management 

KNX 
KNX medium 

TP 1 

Commissioning mode 

S mode 

Rated voltage KNX 

DC 21 V ... 32 V SELV 

Connection mode KNX 

Connection terminal 

Current consumption KNX 

max. 10 mA 

4/5 

82561723 
J:0082561723 

16.03.2010 

KNX IP router 

Содержание IPR 100 REG






Отзывы: