3
2
WARNING
Do not use the floor/wall heater in areas where there is a risk of
explosion or fire from flammable gases. Ensure that the heating
area is kept clear of combustible materials. Do not use the
floor/wall heater in damp areas, without suitable ventilation.
This floor/wall heater is not designed for use within 1m or
above a water source. Do not place within one metre (1m) of
any water source. Do not place directly below or above any
power points or switches.
WARNING: Fire risk exists if this heater is covered by or
positioned close to curtains or other combustible materials.
• This floor/wall heater is intended for domestic/ household
use only.
• Always ensure that this floor/wall heater is installed as per
the requirements noted in Australian Standard AS/NZS
3000:2007.
• Always keep floor/wall heater at least one metre (1m) from
combustible materials.
• DO NOT locate this floor/wall heater directly below or above
the power supply socket or switch.
• DO NOT use this floor/wall heater in either a bathroom or
ensuite.
• DO NOT use a 3rd party timer, or programmable system with
this floor/wall heater.
• DO NOT clean the floor/wall heater while the floor/wall
heater is on or plugged into the mains power supply.
• DO NOT touch any part of the floor/wall heater while on, hot
surfaces may burn.
• DO NOT use the floor/wall heater as a dryer.
• DO NOT attempt to modify the floor/wall heater, power cord,
power plug or the supplied accessories in any way.
• DO NOT expose the floor/wall heater to rain, water, or use in
damp wet conditions.
• NEVER cover this floor/wall heater.
• NEVER carry the floor/wall heater by its power supply cord.
• NEVER use with the power cord coiled, bundled up or tied up.
Always extend fully before use.
• NEVER use the floor/wall heater if any part of it is damaged.
• Ensure that the floor/wall heater is disconnected from the
mains supply when installing,
cleaning or moving.
• Ensure this floor/wall heater is not left on when unattended.
• Ensure the floor/wall heater is not used in areas where
flammable gases are present, e.g. paint, petrol etc.
• Always turn the floor/wall heater OFF at the unit switch and
the power point switch when not in use for extended periods
of time.
• Always allow the floor/wall heater to cool, about one (1)
hour after the floor/wall heater has been turned off, before
cleaning the floor/wall heater.
• Always ensure that the power cord is fully extended and NOT
in contact with any part of the heater.
• Always ensure that the floor/wall heater is kept clean and
free from dust.
• Only use this floor/wall heater when securely attached to the
floor/wall.
ElEctrIcal Data
IMPORTANT
This product is fitted with a sealed electrical connection plug
that is compatible with the floor/wall heater, the mains supply
for Australia and meets the requirements of international
standards. This floor/wall heater must be connected to a supply
voltage that is equal to that stated on the rating label. If the
mains connection plug or power cord becomes damaged it
must be replaced with a complete assembly that is identical
to the original, and this must be replaced by an authorised
service centre. Always follow the Australian requirements for
connection to the mains supply. If in doubt always consult a
qualified electrician.
NOTE: If using this floor/wall heater outside ensure that it is
connected directly to an outdoor power point.
The electrical system of this floor/wall heater must be
connected with an automatic 30mA circuit breaker and/or
residual current device (RCD). If uncertain have a qualified
electrician check your electrical system before installation and/
or use.
All electrical connections are made in a dry area.
Outdoor power points must be weatherproof and installed by a
qualified electrician.
Technical Specification
Floor/Wall Heater
JEH425
Voltage
220-240V AC 50Hz
Input Wattage
1600-1900W
Unit Weight
19Kg (inc. base)
Remote Control Batteries
2 x AAA (not supplied)
Heater specifications can be found on the data label.
Specific Safety
Instructions
