JUKI MO-6800S Series Скачать руководство пользователя страница 33

Страница: 33 / 72

– 21 –

Adjustment procedures

Results of Improper adjustment

1) Adjusting the presser foot position

1. Loosen the presser adjusting screw

❶

and the setscrew

❼

of the

presser foot.

2. Move the presser foot

❻

so that the groove of the presser foot

❻

can align with the groove of the throat plate

❽

. Also the bottom

of the presser foot

❻

can stand on the throat plate

❽

flatly. After

the adjustment, tighten the setscrew

❼

of the presser foot.

3. Loosen the setscrew

❺

, and move the presser foot lifting arm

bushing

❹

to left and right so that the presser arm

❸

can match

the presser bar

❷

and the presser bar

❷

can move upward and

downward smoothly. After the adjustment, tighten the setscrew

❺

4. To adjust to a proper pressure :

Turn the presser adjusting screw

❶

clockwise will increase the

pressure, whereas turn it counterclockwise will decrease the
pressure.

2) Adjusting the lift amount of the presser foot

1. Turn the pulley to lower the feed dog until the bottom of the

presser foot

❻

horizontally comes in contact with the throat plate

❽

2. Provide a 1 mm clearance between presser foot lifting arm

❾

and fixing bracket

. This clearance can be adjusted by slightly

loosening the clamping screw

3. Loosen the nut

. Press the presser foot lifting lever

to lift

the presser foot

❻

from the throat plate

❽

surface. The lift of the

presser foot differs with the model. Adjust the lift of the presser
foot according to the model referring to the table shown below.

Then, adjust the stopper screw

so that it comes in contact with

the presser foot lifting lever

. Tighten the nut

4. After all the adjustments above, please tighten the clamping

screw

(Unit : mm)

機種

1-needle overlock machine MO-6804S

2-needle overlock machine

MO-6814S-2 H

5.5

MO-6814S-3 H

MO-6814S-4 H

MO-6814S-30P

Safety stitch machine

MO-6816S-3 H

5.5

MO-6816S-50H

6.5

MO-6816S-60H

MO-6816S-30P

Uneven contact will result in bad

straight material feed, weak feed
power, or puckering.

Содержание MO-6800S Series









































































Результаты поиска

Содержание MO-6800S Series

Отзывы:

Похожие инструкции для MO-6800S Series

Бренды по названию

Популярные бренды

JUKI MO-6800S Series, Руководство инженера

Результаты поиска

Содержание MO-6800S Series

Отзывы:

Похожие инструкции для MO-6800S Series

Бренды по названию

Популярные бренды