JUKI DDL-8700A-7 Скачать руководство пользователя страница 59

Страница: 59 / 60

– 56 –

E302

Fall detecton swtch falure

(When the safety swtch

works)

• When fall detecton swtch s nput n the

state that the power s turned ON.

• Thread trmmng knfe poston s not cor-

rect.

• Machne-head tlt detector's connector has

come off.

• Check whether the machne head s tlted

wthout turnng OFF the power swtch (sew-

ng machne operaton s prohbted for safety

sake).

• Check whether the fall detecton swtch cord

s caught n the sewng machne or the lke.

• Check whether the fall detecton swtch lever

s caught n somethng.

• Check whether the contact of the tlt detec-

ton swtch lever wth the machne table s

nadequate. (The table has a dent or the

mountng locaton of the bed strut s too far.)

• Check the machne-head tlt detector's con-

nector (CN48) for looseness and slp-off.

E303

Semcrcular plate sensor

error

• Semcrcular plate sensor sgnal cannot be

detected.

• Check whether the machne head corre-

sponds wth the machne type settng.

• Check whether the motor encoder connector

s dsconnected.

E33

Tape cutter devce sensors

are turned ON smultane-

ously

• Faulty operaton of the tape cutter devce.

• Check whether the tape cutter devce s con-

nected properly.

• Check whether the pneumatc pressure s

adequate.

E332

Tape cutter devce sensors

are turned OFF smultane-

ously

• Faulty assembly and adjustment of the

tape cutter devce.

• Check whether the tape cutter devce s

properly assembled.

• Check whether the pneumatc pressure s

adequate.

E499

Data fault

• The stored data have broken.

• Reset all data on the functon settng to the

default values referrng to "Intalzng the

functon settng data" n the Engneer's Man-

ual.

E704

Data fault

• The stored data have broken.

• Reset all data on the functon settng to the

default values referrng to "Intalzng the

functon settng data" n the Engneer's Man-

ual.

E730

Encoder falure

• When the motor sgnal s not properly n-

putted.

• Check the motor sgnal connector (CN30) for

loose connecton and dsconnecton.

• Check whether the motor sgnal cord has

broken snce the cord s caught n the ma-

chne head.

• Check whether the nsertng drecton of the

motor encoder connector s wrong.

E73

Motor hole sensor falure

E733

Inverse rotaton of motor

• Ths error occurs when the motor s run-

nng at 500 st/mn or more n the opposte

drecton of that of rotaton ndcaton dur-

ng motor s runnng.

• Connecton of the encoder of man shaft

motor s wrong.

• Connecton for the electrc power of man

shaft motor s wrong.

E799

Thread trmmng operaton

tme-out

• The thread trmmer control operaton s

not completed wthn the predetermned

tme perod.

• Check whether the functon settng No. 95

(Head selecton functon) has been set cor-

rectly.

• Check whether the motor pulley dameter

agrees wth the settng.

• Check whether the belt has slackened.

E808

Solenod short crcut

• Solenod power does not become normal

voltage.

• Check whether the machne head cord s

caught n the pulley cover or the lke.

E809

Holdng moton falure

• Solenod s not changed over to holdng

moton.

• Check whether the solenod s abnormally

heated. (CTL crcut board asm. Crcut s

broken.)

E80

Solenod current abnormal-

• Solenod rare short-crcut.

• Solenod resstance.

No.

Description of error detected

cause of occurrence expected

Items to be checked

Содержание DDL-8700A-7





























































Результаты поиска

Содержание DDL-8700A-7

Отзывы:

Похожие инструкции для DDL-8700A-7

Бренды по названию

Популярные бренды

JUKI DDL-8700A-7, Инструкция по эксплуатации

Результаты поиска

Содержание DDL-8700A-7

Отзывы:

Похожие инструкции для DDL-8700A-7

Бренды по названию

Популярные бренды