JUKI DDL-8700A-7 Скачать руководство пользователя страница 29

Страница: 29 / 60

– 26 –

Sewing can be performed with the production support data displayed on the control panel.

[Basic operation of the production support modes]

1) When

switch

is pressed in the normal

sewing state, LED

lights up to enter the pro-

duction support mode.

2) Production support function can be changed

over by pressing

switch

3) Data attached marked with (*1) in Table 1 "In-

dicator

" can be changed by means of

switch

and

switch

4) When you keep

switch

held pressed for two seconds, indicator

and LED

flash on and

off. While they are flashing on and off, data marked with (*2) in Table 1 "Display under modes" can be

changed by pressing

switch

and

switch

When you press

switch

, the value marked with (*2) is confirmed and indicator

and LED

stop

flashing on and off.

5) The value with a sharp mark (*3) in Table 1 "Display of modes" can be changed only immediately after

resetting by using

switch

and

switch

6) Refer to the table "Mode resetting operation," for the resetting procedure of data.
7) To return to the normal sewing state, press

switch

Data to be displayed under the respective modes are as described in the table below.

Table 1: Display of modes

Mode name

Indicator

(when

switch

is pressed)

Target No. of pcs. display

mode (F100)

Actual number of pieces (Unit

: piece) (*1)

Target number of pieces (Unit

: piece) (*2)

Target/actual No. of pcs. dif-

ference display mode [F200]

Difference between target

number of pieces and actual

number of pieces (d : piece)

(*1)

Target pitch time

(Unit : 100 msec) (*2)

Sewing machine availability

rate display mode (F300)

oP-r

Sewing machine availability

rate in the previous sewing

(Unit : %)

Display of average avail-

ability rate of sewing

machine (Unit : %)

Pitch time display mode

(F400)

Pi-T

Pitch time in the previous

sewing (Unit : 1sec)

Display of average pitch

time (Unit : 100 msec)

Average number of revolu-

tions display mode (F500)

ASPd

Average number of revolu-

tions in the previous sewing

(Unit : sti/min)

Display of average number

of revolutions

(Unit : sti/min)

Bobbin counter display

mode

bbn

Bobbin counter value (*3)

Содержание DDL-8700A-7





























































Результаты поиска

Содержание DDL-8700A-7

Отзывы:

Похожие инструкции для DDL-8700A-7

Бренды по названию

Популярные бренды

JUKI DDL-8700A-7, Инструкция по эксплуатации

Результаты поиска

Содержание DDL-8700A-7

Отзывы:

Похожие инструкции для DDL-8700A-7

Бренды по названию

Популярные бренды