Judo PROFIMAT JPF-AT DN 100 Скачать руководство пользователя страница 15

Страница: 15 / 44

JUDO PROFIMAT-PLUS

Operation

Operation

ATTENTION

(see chapter “Safety information and
dangers due to non-compliance”)

Imperatively observe the chapter “Intended
use”!

5.1

Commissioning

Before starting up (initial putting into service
or startup after maintenance work),

fill

the

filter with water and

vent

it!

–

To this end, after installation the filter is
filled with water by opening the upstream
shut-off valve.

–

The filter is now under mains pressure.

–

The enclosed air must then be imme-
diately removed from the filter in order to
avoid damage to the installation caused
by water hammers. The filter is vented
by means of backwashing (see chapter
“Backwashing”)

–

After backwashing and venting the filter
is ready for use.

5.2

Control lamps,
manual pushbuttons

Operation

Permanent green light:

the automatic

backwash protective filter is ready for use.

Green light flashing

: The filter is in rinsing

position while plugging in the power supply.
The LED “Operation” is blinking till the flush
valve is closed.

Flushing

Permanent yellow light

: Backwashing is

taking place.

Yellow light flashing

: Call for backwashing

when semi-automatic is set.

Fault

Red flashing light: The automatic back-
wash protective filter is not ready for use
(see chapter “Fault”).

Manual release

Push the manual pushbutton.

Triggers backwashing.

Indication of maintenance

All three control lamps flash at the same
time (see chapter “Warranty and services”).

Fig. 8:

Control lamps, manual pushbuttons

Содержание PROFIMAT JPF-AT DN 100













































Результаты поиска

Содержание PROFIMAT JPF-AT DN 100

Отзывы:

Похожие инструкции для PROFIMAT JPF-AT DN 100

Бренды по названию

Популярные бренды

Judo PROFIMAT JPF-AT DN 100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PROFIMAT JPF-AT DN 100

Отзывы:

Похожие инструкции для PROFIMAT JPF-AT DN 100

Бренды по названию

Популярные бренды