background image

©JRI 

 

16 

 

 

3)

 

Memory management 

The SPY IP can manage its memory in two different ways: Memory full and Rollover Memory. 
In « Memory full » mode the recording will stop as soon as the memory is full. In « Rollover 
Memory » mode, the oldest data are gradually overwritten by new data. These modes are 
managed channel by channel. 
 

4)

 

Alarm Management 

-

 

The

 SPY IP

 detects and manages the alarms in real time regardless of the logging interval. 

In  this  case  it  is  possible  to  go  on  with  the  recording  by  speeding  up  the  pace  of 
measurement to increase the number of points recorded during this event. 

-

 

Le  SPY  IP  manages  different  alarm  statuses  which  are  displayed  on  the  screen  using 
different  colour  codes  (see  4  p8  IV-).    The backlight  is  identical  for  all  the

 

channels  and 

managed according to the following priorities: 
Threshold Alarm (Red) 

   

Technical Alarm (Yellow) 

   

 

Pre-Alarm (Violet) 

   

 

 

Alarm inhibition (Blue) 

   

 

 

 

OK (Green) 

f.ex.: 

if  one  channel  is  in  threshold    alarm  and  another  channel  in  pre-alarm,  then  the 

backlight colour will be the same for all the channels according to the most important even. 
In this case it will be RED. 

-

 

The  threshold  alarms  can  be  either  instantaneous  or  continuous.  In  “instantaneous” 
mode  they  will  disappear  if  the  origin  of  the  alarm  triggering  disappears,  whereas  in 
“continuous” mode they will persist until they have been acknowledged. 

 

5)

 

Password Management  

When  the  operator  is  prompted  to  identify  himself,  the  identification  is  sent  to  Sirius  for 
validation. If accepted it stays active as long as the operator uses the touchscreen whatever 
the operation. Identification is void if the touch screen is not used for a period of 20 seconds. 
You can also disable the entered code by going back to the measurement display by pressing 
this icon  
But  if  the  password  is  rejected  by  Sirius  the  message  "unknown  code"  will  appear  before 
returning to the display prior to the request for identification. 
 

VI.

 

 

CLEANING 

You can clean the device by using a soft cloth duster. DO NOT use water! 

 

VII.

 

RESETTING 

To reset the device, insert a straigthened paper clip or something similar into the small hole on the 
right side of the SPY IP. 
 
 
 
 

Содержание SPY IP 4


















Отзывы: