JR Ergo CCPM, Руководство по сборке

Страница: 47 / 84

The following activation and set-up procedure should be used for all JR XP652 systems. Please note that the XF622 and XP642 6 channel
systems Do Not have the required CCPM software, and therefore cannot be activated by the Horizon Service Center.
Prior to activating the CCPM function, it is first suggested that the Data Reset Function be performed to reset the desired model number
to be used back to the factory default settings.
Caution: Prior to performing the Data Reset Function, it will be necessary to select the desired model number to be used.
A) Press the MODE and CHANNEL Keys simultaneously while turning the power switch
on to enter the System Mode. Next, press the CHANNEL key until MDL (Model Select)
appears on the screen, and choose the desired model number to be used.
B) Press the MODE key until RST (Data Reset) appears on the screen. Press the + and -
keys simultaneously to reset the current model. A high pitched beep will indicate that
the reset was successful. Press the MODE and CHANNEL keys simultaneously to exit
the system mode.
C) With the power switch still on, press the MODE and CHANNEL keys simultaneously to
enter the Function Mode. Press the MODE key until MIX CCP (CCPM mixing) appears
on the screen. Press the + or - keys to activate the CCPM function. Mix CP2 should
appear on the screen. Next, press the CHANNEL key until MIX CP6 appears on the screen. It will be necessary to change the value of
CP6 (Channel 6, Aux1) from +60 to -50 using the - key.
D) Press the MODE key until the servo reversing screen appears on the screen. Next, reverse the Throttle (THR), Aileron (AIL) and Rudder
(RUD) channels by pressing the CHANNEL key to select the desired channel, and then the + or - keys to set the servo direction.
E) Press the MODE key until TRV ADJ (Travel Adjust) appears on the screen, and adjust the travel values as shown by pressing the
CHANNEL key to select the desired channel, and then the + or - key to set the desired travel value. Press the MODE and CHANNEL keys
simultaneously, or turn the power switch off, to exit the Function Mode. Please note that the throttle travel values may vary based upon
the type of engine used. This value can be fine tuned once the throttle linkage has been installed.
Note: The travel values shown for the rudder function are for use with Piezo gyros, like the JR NEJ-900, NEJ-400, NEJ-450, or NEJ-3000
type gyros. If a conventional mechanical type gyro is used (JR 120, 130, etc.), then the travel values of the rudder will need to be
reduced to approximately 100%.
CCPM SOFTWARE ACTIVATION AND INITIAL ADJUSTMENT CONT.
3 9
3. JR XP652 SYSTEMS
mdl
1
Indicates Model Select
Indicates Current Model
rst
he
Indicates Data Reset
Indicates Model Type
m i x
CCP
of
Indicates CCPM Mixing
Indicates Inhibited
thr
r e v.n o r m
thro
trv adj
- 1 3 0
ail
- 1 2 0
ele
- 1 2 0
rud
-150
pit
- 1 2 0
ail
r e v.n o r m
rud
r e v.n o r m
m i x
C
P
6
— 50 %
Indicates Channel 6 (Aux 1, Right Servos)
Indicates Value Set – 50%
Indicates Channel
Indicates Reversed
Indicates Channel
Indicates Reversed
Indicates
Channel
Indicates Reversed
thro
prv adj
- 1 1 0
ail
- 1 0 0
ele
- 1 0 0
rud
-150
pit
- 1 0 0
Ch
Ch
Ch
Ch
Ch
Ch
Ch
Ch
Digital Servos, Super Servos
Standard Servos