JR ProPo Ergo Z230 Скачать руководство пользователя страница 12

Страница: 12 / 72

Note: Be sure to use the two

shorter Body Mount
Standoff for this installation.

Note: Due to the addition of the

Frame Double Plates, only
four 3mm Flat Washers are
required for this step.

* This hardware is packaged seperately

with the two Frame Doubler Plates.

3x8mm Socket Head Bolt

..........22 pc

Body Mounting Standoff

..........2 pc

3mm Flat Washer

..........11 pc

3x6mm Socket Head Bolt

..........1 pc

2.6x8mm Self Tapping Screw

..........4 pc

3mm Lock Nut

..........2 pc

Tail Control Rod Guide

3x6mm Socket Head Bolt

Body Mounting Standoff: Short

Bearing side must face upward

3mm Flat Washer

(11 pc)

Frame Double Plate

(2pc)

Bearing side must

face downward

*3mm Lock Nut

(2pc)

Servo Mounting Plates

2.6x8mm Self Tapping

Screws

2-1

UPPER MAIN FRAME SECTION ASSEMBLY

Upper Main Shaft Bearing Block

When installing the Main Rotor Shaft Bearing Blocks, it is important to note the correct direction in which they need to be installed.
Please refer to the diagram below for clarification.

Position so the side of
the bearing block that
has the bearing flush
with the flange is upward.

Lower Main Shaft Bearing Block

Position so side of the
bearing block that has the
bearing flush with the
flange is downward.

Bearing Flush
with Flange

Bearing

Bearing Flush
with Flange

Use Threadlock

3x8mm Socket Head Bolt

(21 pc)

Z,Q

Содержание Ergo Z230









































































Результаты поиска

Содержание Ergo Z230

Отзывы:

Похожие инструкции для Ergo Z230

Бренды по названию

Популярные бренды

JR ProPo Ergo Z230, Руководство по сборке

Результаты поиска

Содержание Ergo Z230

Отзывы:

Похожие инструкции для Ergo Z230

Бренды по названию

Популярные бренды