manualshive.com logo in svg

JPS Communications NXU-2, Инструкция по установке и эксплуатации

Поделиться
Скачать
JPS Communications NXU-2 Скачать руководство пользователя страница 43

NXU-2 Operations Manual 

 

 

 

JPS Communications, Inc.

 

5-1 

5  NXU-2 Troubleshooting 

The following table may be used to troubleshoot any problems you may encounter during 
installation or operation of the NXU-2. 

Table 5-1 

Troubleshooting 

Symptom: 

Possible Causes: 

Main Power LED is not illuminated 

Check that AC adapter is firmly plugged in 
If user supplied power plug, check for proper 
voltage, current, and polarity per Section 2.6 
Power Requirements. 

Cannot place the unit into Command Mode as 
outlined in Section 3.3  

Check RS-232 connections 
Verify terminal settings: 9600 baud, 8 data 
bits, 1 stop bit, no parity  
(

Note: if you have previously used Command 

Mode to set the serial port baud rate to a 
value different than 9600 then you must use 
the new baud rate to enter Command Mode

.) 

Verify that no flow control, either hardware or 
software, is being used in your terminal 
program. 
Make sure you wait at least 5 seconds, and 
then type +++ (three plus signs) within 1 
second. 

Settings made in Command Mode do not 
appear to take effect. 

You must issue a SAVE command after 
making changes in order to save the new 
settings and restart the NXU-2. 

Client and Server units are properly 
configured and online but LINK ACTIVE is 
not on. 
 
 
 
 
 
 
 
 
 
 
 
 
 

Verify that both the Client and Server NXU-2 
units are “visible” on the network by 
“pinging” their IP addresses from a network-
connected computer. 
Verify that the Server’s IP address has been 
programmed into the Client using the SRVRIP 
command per Section 3.3.7 Client/Server 
Selection OR 
If there is not a default server programmed 
into the client, verify that a manual connection 
has been entered per Section 4.5 Controlling 
Connections 
Verify that the PORT has not been changed. 
from the default value of 1221, or if it has, 
make sure the PORT value is the same on both 
Client and Server. 

Содержание NXU-2






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды