manualshive.com logo in svg

JPS Communications NXU-2, Инструкция по установке и эксплуатации

Поделиться
Скачать
JPS Communications NXU-2 Скачать руководство пользователя страница 37

NXU-2 Operations Manual 

 

 

 

JPS Communications, Inc.

 

4-1 

4  Operation 

4.1  General 

This Section contains information and instructions required for proper operation of the NXU-2.  
Refer to Figure 2-2 

Control and Connector Locations for views of controls and connectors. 

4.2  Front Panel Indicators 

All front panel indicator LEDs are explained below, starting at the left side of the unit. 

4.2.1  Power LED 

This yellow LED lights whenever DC power is applied to the unit. 

4.2.2  Link Active LED 

The green Link Active LED is illuminated whenever the NXU-2 has an IP connection open to 
another NXU-2 on the network. If this indicator is not lit, either the NXU-2 does not have an 
active VoIP connection or the connection has been lost. 

4.2.3  Channel Active LED 

This green LED is lit whenever COR is active. This also indicates that the NXU-2 is sending 
audio data across the IP link. 

4.2.4  Audio Input LED 

This yellow LED is provided as a visual aid in setting the proper input audio level for optimal 
operation.  See Section 4.4.2 Input/Output Level Adjustments for instructions. 

4.3  Rear Panel Connectors, Adjustments and Level Potentiometers 

Section  2.8  Rear Panel Adjustments and Connectors contains full explanations and pin-outs for 
all rear panel connectors.  Figure 2-2 displays connector locations.    

4.4  NXU-2 Operation 

Basic operation and control of the NXU-2 is discussed in the following paragraphs.  These 
instructions assume the NXU-2 has already been correctly configured per Section  3 
Configuration. 

Содержание NXU-2






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды