manualshive.com logo in svg

JPS Communications NXU-2, Инструкция по установке и эксплуатации

Поделиться
Скачать
JPS Communications NXU-2 Скачать руководство пользователя страница 2

NXU-2 Operations Manual 

 

 

2

 

JPS Communications, Inc. 

 

Warranty 

JPS Communications, Inc. warrants its manufactured equipment to be free from defects in 
materials and workmanship, and to conform to published specifications for a period of 18 
months from the date of shipment from the factory or 12 months from installation, whichever 
occurs first. 

JPS warrants its service work performed in connection with this warranty to be free from defects 
in materials and workmanship for a period of 90 days from the date the work is performed. 

If a defect occurs within the warranty period, the buyer shall notify JPS immediately. JPS will 
repair or replace the equipment at its option, upon return of the equipment, shipping prepaid, to 
the JPS facility in Raleigh, North Carolina, USA 

This  warranty does not apply to damage caused by accidents, abuse or improper installation. 

NO OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT 
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY. 

 

NOTICE 

JPS Communications, Inc. reserves the right to make changes to the equipment 
and specifications without prior notice. 

 

PROPRIETARY STATEMENT 

The information contained in this manual is the property of JPS 
Communications, Inc. and is intended for the purchaser’s use only. It may not 
be reproduced without the express written consent of JPS Communications. 

 

 

 

JPS Communications, Inc.

 

5800 Departure Drive 

Raleigh, NC 27616 

Email: [email protected] 

Phone: (919) 790-1011 

Fax: (919) 790-1456 

Содержание NXU-2






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды