Jøtul FS 84 - 370 Скачать руководство пользователя страница 25

Страница: 25 / 68

ENGLISH

Please note that it is extremely important for connections to
have a degree of flexibility. This is to prevent any movement in
the installation leading to the formation of cracks.

For recommended chimney draught, see “2.0 Technical data”

Flue pipe at top outlet - fig. 4

The product is supplied from the factory with the smoke outlet
fitted for the top outlet. Offset pipe, 50 mm, for the top outlet is
supplied as an optional extra.

1. Place the gasket on the edge of the offset pipe

(fig. 4A)

2. Fit the end of the offset pipe with the gasket into the smoke

outlet.

(fig. 4B).

3. Check that the whole of the gasket is correctly positioned.

4.3 Low model

The low model consists of the following parts
– see fig. 5A:

Part 1.  Bottom plate
Part 2.  Connection angle
Part 3.  Base
Part 4.  Adjusting kit
Part 5.  Rear section
Part 6.  Side frame, left
Part 7.  Side frame, right
Part 8.  Threaded bar with washers and nuts
Part 9.  Cowl 1
Part 10. Sealing plug

(only for top outlet)

Part 12. Top crown
Part 13. Top grate
Part 14. Floor plate (optional extra)

The bottom plate

(part 1)

should be put in place. Check it is

level using a spirit level and adjust as necessary using adhesive
or mortar. It is extremely important that the bottom plate be
steady and level.

2. The base

(part 3)

should be inserted in slots in the bottom

plate. Check that it is level.

3. Move the burn chamber into position. When using the outside

air connection (optional extra,

cat. no. 341296)

, this must be

fitted now. Position the burn chamber in the four grooves in
the base

(part 3)

See

fig. 6

. Make sure that the flexible hose

for combustion air is not trapped. Route the hose out through
the hole in the rear of the base

(part 3)

. Suggested installation

of the flexible hose: See

fig. 10 A, B and C

. Remove the pieces

of wood carefully so that the burn chamber does not topple
over. The approval label, which is attached by a wire, is fed
under the burn chamber and down into the base.

4. Adjust the burn chamber horizontally so that it is flush with the

front of the base.

See fig. 6.

Level and adjust the burn chamber

vertically using the long nuts in the adjusting kit (part 4).

NB: It is

extremely important for the burn chamber to be vertically level!

5. Move the rear section

(part 5)

into position. The rear section has

two protrusions,

fig. 7A

which fit into slots in the base,

fig. 7B.

Adjust the burn chamber to fit the hollow on the inside of the
rear plate. See

fig. 8.

6. Move the side frames into position

(parts 6 and 7)

NB: The side

frames must be flush with the base (part 3) and be attached
using acrylic adhesive.

7. Push the threaded bar (part 8) through the hole in the base

and lock it underneath with nut and washer. Then thread the
connection angle (part 2) on the threaded bar (part 8) and hook
it onto the insert. Lock in place with nut.

NB: Tighten the nut

carefully!

See

fig. 9 A + B.

8. Move cowl 1

(part 9)

into position in the slots.

NB: When top

mounting is used, glue the sealing plug (part 10) in place using
acrylic adhesive.

9. Move the top crown

(part 12)

into position.

10.

Installation using a top outlet/steel chimney:

The product is supplied from the factory with the smoke outlet

fitted for the top outlet.

• Fit an offset pipe,

50 mm

(optional extra).

• Make sure that the gasket is properly seated between the

offset pipe and the smoke outlet.

• Insert the top grate

(part 13). NB: The small arrow in the centre

of the grate must be turned forwards. See fig. 11.

• Mount an uninsulated pipe from the offset pipe to approx.

over the top grate. Thread the flue pipe through the top

grate (part 13), then place it in the offset pipe.

• Then fit the steel chimney in accordance with the chimney

supplier’s operating instructions. See

fig. 2.

11. Installation using a rear outlet:

• Use the smoke outlet installed for the top outlet. Fit the flue

pipe in accordance with the instructions from the smoke outlet
to the chimney through the hole in cowl 1 (part 9). See 4.2.

• Insert the top grate

(part 13). NB: The small arrow in the centre

of the grate must be turned forwards. See fig. 11.

4.4 High model

The high model consists of the following parts
– see fig. 5B:

(only for top outlet)

Part 11. Cowl 2
Part 12. Top crown
Part 13. Top grate
Part 14. Floor plate (optional extra)

The bottom plate

(part 1)

should be put in place. Check it is

level using a spirit level and adjust as necessary using adhesive
or mortar. It is extremely important that the bottom plate be
steady and level.

2. The base

(part 3)

should be inserted in the slots in the bottom

plate. Check that it is level.

3. Move the burn chamber into position. When using the outside

air connection (optional extra,

cat. no. 341296)

, this has to be

fitted now. Position the burn chamber in the four grooves in
the base

(part 3)

See

fig. 6

. Make sure that the flexible hose

for combustion air is not trapped. Route the hose out through
the hole in the rear of the base

(part 3)

. Suggested installation

of the flexible hose: See

fig. 10 A, B and C

. Remove the pieces

of wood carefully so that the burn chamber does not topple
over. The approval label, which is attached by a wire, is fed
under the burn chamber and down into the base.

4. Adjust the burn chamber horizontally so that it is flush with the

front of the base.

See fig. 6.

Level and adjust the burn chamber

vertically using the long nuts in the adjusting kit (part 4).

NB: It is

extremely important for the burn chamber to be vertically level!

5. Move the rear section

(part 5)

into position. The rear section has

two protrusions,

fig. 7A