Jonsered CS 2163 Скачать руководство пользователя | Manualshive

Страница: 10 / 40

background image

10 –

English

SAFETY INSTRUCTIONS

Chain

A chain is made up of a number of links, which are available
in standard and low-kickback versions.

Combining these links in different ways gives different
degrees of kickback reduction. In terms of kickback reduction
alone, four different types of link are available.

Some terms that describe the bar and chain

When the cutting equipment supplied with your saw becomes
worn or damaged you must replace it with one of the bars and
chains recommended by us. See the Technical data section.

Bar

•

Length (inches/cm)

•

Number of teeth on bar tip sprocket (T). Small number =
small tip radius = low risk of kickback.

•

Chain pitch (inches). The spacing between the drive links
of the chain must match the spacing of the teeth on the
bar tip sprocket and drive sprocket.

•

Number of drive links. The number of drive links is
determined by the length of the bar, the chain pitch and
the number of teeth on the bar tip sprocket.

•

Bar groove width (inches/mm). The groove in the bar must
match the width of the chain drive links.

•

Chain oil hole and hole for chain tensioner. The bar must
be matched to the chain saw design.

Chain

•

Chain pitch (inches)

•

Drive link width (mm/inches)

•

Number of drive links.

•

Level of kickback reduction. The level of kickback
reduction offered by a chain is only indicated by its model
number. See the Technical data section to find the model
numbers of chains that are recommended for use with
your model of chain saw.

Sharpening your chain and adjusting raker
clearance

General information on sharpening cutting teeth

•

Never use a blunt chain. When the chain is blunt you have
to exert more pressure to force the bar through the wood
and the cuttings will be very small. If the chain is very blunt
it will not produce any cuttings at all. Wood powder would
be the only result.

None

Standard

Low-kickback

Cutting link

Drive link

Side link

Level of kickback
reduction

Cutting link

Drive link

Side link

Low

Standard

High

Extra high

!

WARNING! The risk of kickback is increased
with a badly sharpened chain!

«
...
8
9
10
11
12
...
»

Содержание CS 2163









































Отзывы:

Нет отзывов

Похожие инструкции для CS 2163

Бренд: Oleo-Mac Страницы: 32

Бренд: EINHELL Страницы: 36

Бренд: NAX Страницы: 140

Бренд: Feider Страницы: 23

Бренд: Echo Страницы: 32

Бренд: Makita Страницы: 21

Бренд: Hitachi Koki Страницы: 80

Бренд: Hitachi Koki Страницы: 118

Бренд: Gardol Страницы: 172

Бренд: Craftsman Страницы: 19

Бренд: Turbo-Silent Страницы: 78

Бренд: HIKOKI Страницы: 216

Бренд: EINHELL Страницы: 2

Бренд: EINHELL Страницы: 64

Бренд: EINHELL Страницы: 104

Бренд: EINHELL Страницы: 108

Бренд: EINHELL Страницы: 132

Бренд: EINHELL Страницы: 139

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды