Jonsered CS 2163 Скачать руководство пользователя

Страница: 2 / 40

2 –

English

KEY TO SYMBOLS

Key to symbols

WARNING! Chain saws can be dangerous!
Careless or incorrect use can result in
serious or fatal injury to the operator or
others.

Please read the operator’s manual carefully
and make sure you understand the
instructions before using the machine.

Always wear:

•

Approved protective helmet

•

Approved hearing protection

•

Protective goggles or a visor

This product is in accordance with applicable
EC directives.

Noise emission to the environment
according to the European Community’s
Directive. The machine’s emission is
specified in chapter Technical data and on
label.

Switch off the engine by moving the stop
switch to the STOP position before carrying
out any checks or maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

Refuelling.

Filling with oil and adjusting oil flow.

Other symbols/decals on the machine refer to special
certification requirements for certain markets.

Содержание CS 2163









































Результаты поиска

Содержание CS 2163

Отзывы:

Похожие инструкции для CS 2163

Бренды по названию

Популярные бренды

Jonsered CS 2163, Руководство оператора

Результаты поиска

Содержание CS 2163

Отзывы:

Похожие инструкции для CS 2163

Бренды по названию

Популярные бренды