Johnson AFG Pro 7.2AT, Руководство по обслуживанию

Страница: 29 / 34

4.6 RUNN
1) Remove
2) Remove
3) Remove
4) Remove
5) Remove
6) Reverse
Note1:
1. Adjust
2. The run
belt.
Note:2
ADJUSTING
After plac
centering. T
cause the b
direction be
Step1: Loca
frame at the
prevent ove
Step2: The
do not start
center the b
loosened th
Step3: Whil
Right bolt by
left tighten t
remains cen
Step4: Chec
should not h
necessary.
NING BELT
the motor co
the rear rolle
the running
the front roll
the running
e Steps 1-5 t
t running belt
nning deck is
G THE RUN
cing the tread
The belt may
belt to stretch
elow.
ate the two h
e back of trea
er tightening
belt should h
the treadmil
belt by pushin
hem, approxi
e the treadm
y turning it cl
the left bolt b
ntered for se
ck the tensio
hesitate or sl
CHA
T REPLAC
over as outlin
er as outlined
deck as outl
er as outline
belt
to install a ru
t tension afte
s silicon on o
NING BELT
dmill in the p
need to be a
h at different
ex head bolt
admill. These
of one side.
have equal d
l. Turn the b
ng the belt fr
mately one f
mill is running
lockwise 1/4
by turning it c
everal minute
on of the belt
lip. If this occ
APTER 4:
CEMENT
ned in Sectio
d in Section 4
ined in Secti
ed in Section
F
unning belt. (
er replaceme
ne side . New
T
osition it will
adjusted afte
rates. If the
t on the rear
e bolts adjust
istance on e
olts counter
rom side to s
full turn. Insp
g at 3 mph, o
turns, and lo
lockwise 1/4
es.
. The belt sh
curs, tighten
Part Rep
on 4.1.
4.2.
on 4.4.
4.5.
Fig-1
(Fig-1 & Fig-2
ent (Note2)
w deck surfa
be used, the
er the first 2 h
belt starts to
of the treadm
t the rear roll
either side be
clockwise ap
side. Tighten
pect the belt f
observe the b
oosen the lef
4 turn and loo
hould be very
the belt by t
placement
2)
aces must AL
e belt must b
hours of use
o slip when a
mill. The bolt
ler. Do not ad
etween the fra
pproximately
the bolts the
for damage.
belt position.
ft bolt 1/4 turn
osen the righ
y snug. When
urning both b
Guide
LWAYS be m
be checked fo
. Temperatur
user is on it
ts are located
djust until the
ames. If the b
y one full turn
e same amou
If it is movin
n. If it is mov
t 1/4 turn. Re
n a person w
bolts clockwi
matched to a
or proper ten
re and humid
, be sure to f
d at each en
e treadmill is
belt is touchi
n on each sid
unt as when
ng to the righ
ving to the lef
epeat step 3
walks or run o
ise 1/4 turn,
29
Fig-2
new running
nsion and
dity, and use
follow the
d of the
s on. This will
ing one side,
de. Manually
the user
t, tighten the
ft, tighten the
until the belt
on the belt, it
Repeat if
9
g
e
l
,
e
e
t
t