background image

10 - 11 

MAINTENANCE PROCEDURE G260 – REVISION 02 - 2013-04 

 
9. 

If the cracking effort is lower then indicated, use the 4 mm 
Allen key and screw by a ¼ turn the fine adjustment screw 
inside the adjustment knob. 
 

note :

 The adjustable orifice 

MUST

 always be readjusted as per paragraph 5 and 6 

before measuring the cracking effort again. 
 
Proceed by successive steps to reach the recommended values(1,0 to 1,2 inches of 
water or 2,5 to 3,0 milibars). 
 

10.  Check the final adjustment: it must be possible to push the purge button 1 mm with-

out a leakage of the 2

nd

 stage. 

 
11.  Remove the adapter mouthpiece of the Digi-Mag from the G260 mouthpiece. 
 
12.  Fit the plug in the adjustment knob. 
 
13.  Close the tank valve, purge and remove the 2

nd

 stage adjustment tool. 

 

note

: before removing the 2

nd

 stage adjustment tool, make sure that the adjustment 

knob is retracted out of the groove in the orifice to ensure that the 2

nd

 stage adjust-

ment tool is no longer connected to the orifice. Otherwise the adjustment can be 
changed while unscrewing the 2

nd

 stage adjustment tool. 

 
14.  Slightly grease the thread on the inlet tube and L.P. hose, screw the L.P. hose on the 

2

nd

 stage and reposition the sleeve(s). 

 
 

Содержание SCUBAPRO G260












Отзывы: