Johnson Electric AB51 Скачать руководство пользователя страница 39

Страница: 39 / 50

AB5 and AB51 Drivers User Manual

Technical Data

Nanomotion Ltd.

How It Works

5.3.5

The TP feature is designed with the following motor calculated

temperature settings:

•

Motor temperature below 85°C - normal operation.

•

Motor temperature between 85°C to 100°C - warning mode.

Displayed by a blinking TP LED and an on\off Fault output signal

(pin #3 in the 25 pin I/O port connector).

•

Motor temperature above 100°C - the motor is disabled. The TP

LED is constantly on and so is the Fault output (pin #3). The

driver remains disabled until motor temperature drops to 85°C

(natural cooling).

•

Motor temperature back under 85°C - once the driver computed

the motor has cooled to just under 85°C, the TP LED will blink

once and remain on and so will the Fault output signal. To resume

operation, the driver will now need to be disabled and then

Enabled again.

Normal
operation

Warning
zone

Shut down
zone

TP LED

Off

Blinking

Fault output (pin #3)

Off

Toggles on/off

Motor

Enabled

Disabled

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание AB51



















































Результаты поиска

Содержание AB51

Отзывы:

Бренды по названию

Популярные бренды

Johnson Electric AB51, Руководство пользователя

Результаты поиска

Содержание AB51

Отзывы:

Бренды по названию

Популярные бренды