manualshive.com logo in svg

Johnson Electric AB51, Руководство пользователя

Поделиться
Скачать
Johnson Electric AB51 Скачать руководство пользователя страница 17

AB5 and AB51 Drivers User Manual  

 

Connecting the AB5/AB51 Driver 

 

Nanomotion Ltd.  

 

16

 

  Wires and Connectors 

2.1.1

•

 

Power supply:

 use 22 AWG (or lower AWG) wires for the power 

supply. For noisy surroundings, it is recommended to twist the 

ground line and the power line together.  

•

 

Analog command:

 a twisted shielded cable is recommended. 

•

 

Discrete inputs:

 these signals are not sensitive to noise and can 

be grouped together in the same harness with any of the other 

groups. 

Connector 

Description 

Control 
terminal 

 

5 pin connector. Re24V from an external source 
and provides direct control over the motor ENABLE signal 
and the analog control signal (+Vin and/or -Vin). (Mating 
connector is by Wieland, P/N 25.621.0553.0). See Table 6 
for connector pinout. 

I/O Port 
Connector 

25 pins D-type female connector. Interfaces to the control 
source (joystick or controller). See Table 8 for connector 
pinout. 

Motor 
Output Port 

9 pins D-type male connector. Interfaces to the motor. 
See Table 7 for connector pinout. 

Table 1: Front Panel Connectors 

  Motion Control Interfaces 

2.1.2

The AB5/AB51 driver can receive the input signals either from a 

motion controller or from a joystick. The schematic diagrams of the 

motion controller and joystick connections to the AB5/AB51 driver are 

provided in following sections. 

Note: 

 

The motor may be operated from the Terminal block using the following signals: +24V, 

◘

GND, +Vin, -Vin, Enable. 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание AB51



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды