background image

 

Setting the Mechanical Cooling Mode (C mech) 

This setting determines whether to allow the operation 
of mechanical cooling if the free cooling (economizer) 
cannot maintain the cooling setpoint. 

• 

Selecting 

off

 means the mechanical cooling never 

operates at the same time as the free cooling. This 
option typically applies when the mixed air 
temperature sensor is installed after the 
mechanical cooling coils. 

• 

Selecting 

on

 enables mechanical cooling to 

operate when the free cooling (economizer) 
cannot maintain the cooling setpoint. This option 
typically applies when the mixed air temperature 
sensor is installed before the mechanical cooling 
coils. 

To set the mechanical cooling mode while in the 
Installer Configuration Menu: 

1.  Answer NO to all prompts until the mechanical 

cooling mode prompt appears in the display. Press 
YES to enter the Mechanical Cooling Mode Menu. 

2.  Use the UP/DOWN arrow keys to choose on or off. 

Press YES to store the selection. 

The display now shows the Mixed Air Setpoint Menu. 
See the 

Setting the Mixed Air Temperature Setpoint

 

(Mix stpt)

 section for instructions. 

Setting the Mixed Air Temperature Setpoint 
(Mix stpt) 

The mixed air temperature setpoint establishes the 
mixed air temperature when operating in the 
economizer mode. The economizer is adjusted 
accordingly to maintain the mixed air temperature 
setpoint. 

The mixed air temperature setpoint is adjustable from 
50 to 90

°

F (10 to 32

°

C). 

To adjust the mixed air temperature setpoint while in 
the Installer Configuration Menu: 

1.  Answer NO to all prompts until the mixed air 

setpoint prompt appears in the display. Press YES 
to enter the Mixed Air Setpoint Menu. 

2.  Use the UP/DOWN arrow keys to adjust the mixed 

air setpoint. Press YES to store the temperature. 

The display mixed air temperature prompt is now 
displayed. See the 

Displaying the Mixed Air 

Temperature (Display)

 section for instructions. 

Displaying the Mixed Air Temperature (Display) 
(Only Available if Mixed Air Temperature Sensor is 
Installed) 

The mixed air temperature can be displayed if a mixed 
air temperature sensor is installed. The temperature 
can be used to help service and troubleshoot the 
equipment and economizer operation. The mixed air 
temperature is only accessible through the Installer 
Configuration Menu. 

To access the mixed air temperature while in the 
Installer Configuration Menu: 

1.  Answer NO to all prompts until the display mixed 

air temperature prompt appears in the display. 
Press YES to display mixed air temperature. 

2.  The mixed air temperature is displayed. After 

about 45 seconds the TEC2104-1 returns to the 
Status Display Menu or press YES to advance to 
the exit menu display. 

3.  Press YES to exit the Installer Configuration Menu 

or press NO to return to the beginning of the menu 
(digital input configuration). 

Operation 

Programming/Operating the TEC2104-1 

Once the TEC2104-1 is configured through the 
Installer Configuration Menu, the thermostat’s 
operating parameters can be programmed through the 
Main User Menu (access the Main User Menu by 
pressing the MENU key during normal thermostat 
operation). The Main User Menu contains the basic 
operating features of the TEC2104-1. The Main User 
Menu uses Auto Help. When there is a pause in 
programming activity, Auto Help automatically appears 
in the Main User Menu. To exit Auto Help, continue 
with the Programming selection. 

When the thermostat is in the Main User Menu and is 
left unattended for 45 seconds, it reverts to the Status 
Display Menu. 

14    

TEC2104-1 Networked Multi-Stage Economizer Thermostat Installation Instructions 

Содержание TEC2104-1




















Отзывы: