Johnson Controls System 350 P352AB Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 12

Johnson Controls System 350 P352AB Series Скачать руководство пользователя страница 4

4

Basic Controls—System 350 P352AB Electronic Pressure Control Series Product/Technical Bulletin

A

djustments (P352AB Control)

Perform the following steps to adjust the P352AB
control settings. (See Figure 3.) Refer to Figure 5 for
an example of the P352AB control in a typical Direct
Acting/Reverse Acting application.

!

WARNING:

Risk of Electrical Shock.

Disconnect power supply to
avoid possible electrical shock or
equipment damage. More than
one disconnect may be required
to completely de-energize
equipment.

1. Ensure all power to system is off.

2. Remove the P352AB control cover by loosening

the four captive cover screws.

3.

Set the mode of operation

by positioning the

jumpers (at Jumper Terminal J1) horizontally for
Direct Acting or vertically for Reverse Acting.

Note: The P352AB controls are configured in the

DA mode at the factory.

4.

Adjust the differential

using the potentiometer

marked DIFF ADJUST to the desired setting.
Clockwise rotation increases the differential.

5.

Adjust the setpoint

using the setpoint adjustment

dial to the desired setting.

After power is applied to the control, a more
accurate setting of the setpoint can be made by
utilizing the D352A Pressure Display Module.

6. Replace the cover on the control and fasten in

place with screws.

7. Restore power to system.

Module

Connector

Concealed Setpoint

Adjustment Dial

Differential

Potentiometer

N.C.

Relay

N.O.

Terminals

COM

Output

Relay Energized

LED Indicator

Jumper

Position at J1

Reverse Acting

Direct Acting

Cover Screw

(One of Four)

24V

COM

VDC
SEN

Wire

Terminal

Block

Relay

Figure 3: Interior View and Typical Wiring of the P352AB Control

A

dd-On Modules

The Y350R Power Module, D352 Digital Pressure
Display, and S352A Stage Modules snap together and
plug into the P352AB Electronic Pressure Control via
connectors on both sides of each add-on module.

Y350R Power Module

The Y350R Power Module provides a convenient
method of powering System 350 modules from a
120 or 240 VAC power source.

The Y350R Power Module can be plugged into the
right side of the P352AB controls or any of the add-on
modules. The Y350R Power Module is capable of
providing power to a P352AB control, a D352 Display
Module, and up to five S352A Stage Modules. (Refer
to the

System 350

TM

Y350R Power Module

Product/Technical Bulletin, LIT-930090

, for more

information.)

«
...
2
3
4
5
6
...
»

Содержание System 350 P352AB Series













Отзывы:

Нет отзывов