Johnson Controls PGP922 Скачать руководство пользователя страница 1

Страница: 1 / 16

PGP922 Glass Break Detector Installation

Guide

Installation guidelines

The reference to PGP922 throughout this manual includes the model PGP9922.

CAUTION:

Only qualified personnel may install this equipment. Place this device in non-

hazardous indoor locations only.

Important:

Check the device and the entire alarm system weekly to ensure optimal

performance.

Note:

To comply with FCC and ISED Canada RF exposure compliance requirements, locate the device

at a distance of at least 20 cm from all persons during normal operation.
Do not co-locate the antennas used for this product, or operate them in conjunction with any

other antenna or transmitter.
Install the PGP9922 in accordance with the Standard for Installation and Classification of

Residential Burglar Alarm Systems, UL 1641 and ULC-S302.

Figure 1: PGP922

Callout

Description

LED

Microphone

Snap

Battery pull-tab

For more information refer to section

About PGP922

D-308652

*D-308652*

D-308652 PGP922 Rev.0

Содержание PGP922

















Результаты поиска

Содержание PGP922

Отзывы:

Похожие инструкции для PGP922

Бренды по названию

Популярные бренды

Johnson Controls PGP922, Руководство по установке

Результаты поиска

Содержание PGP922

Отзывы:

Похожие инструкции для PGP922

Бренды по названию

Популярные бренды