background image

UL/ULC notes

Only model PGP9922 operating in the frequency band 912-919MHz is UL/ULC listed. The PGP9922

has been listed by UL/ULC for commercial and residential burglary applications in accordance

with the requirements in the Standards UL 634 and ULC/ORD-C634 for contacts and switches. For

UL/ULC installations use this device only in conjunction with compatible DSC wireless receivers:

HSM2HOST9, HS2LCDRF(P)9, HS2ICNRF(P) 9, HS2LCDRFPRO9, PG9920, and Qolsys IQPanel2, IQHub,

IQPanel4. After installation, verify the product functionality in conjunction with the compatible

receiver used.

Safety Instructions

Read the safety information before you install the equipment.
The detector shall be installed and used within an environment that provides the pollution degree

max 2 and over voltages category II in non-hazardous locations, indoor only. The equipment is

designed to be installed by SERVICE PERSONS only; (SERVICE PERSON is defined as a person having

the appropriate technical training and experience necessary to be aware of hazards to which that

person may be exposed in performing a task and of measures to minimize the risks to that person

or other persons).

W.E.E.E Product recycling declaration

For information regarding the recycling of this product you must contact the

company from which you originally purchased it. If you are discarding this

product and not returning it for repair then you must ensure that it is returned

as identified by your supplier. This product is not to be thrown away with

everyday waste.

Directive 2012/19/EU Waste Electrical and Electronic Equipment.

About PGP922

The PGP922 is a wireless PowerG two-way acoustic glass-break detector designed to detect the

breaking of framed glass mounted in an outside wall. This device is wall or ceiling mountable

and suitable for most types of window or door glass, including the following: plate, tempered,

laminated, wired, coated, and sealed insulating glass.
The device has the following features:

The device is fully pre-calibrated

Provides temperature and light level reports for PowerG control panels that support this

feature

Alarm and other data are forwarded to the control panel

Back-tamper protection

Periodic supervision message is transmitted automatically to the control panel at regular

interval

A bicolor LED lights whenever events are reported

Remote firmware upgrade

Limited Warranty

Digital Security Controls warrants that for a period of 12 months from the date of purchase, the

product shall be free of defects in materials and workmanship under normal use and that in

fulfilment of any breach of such warranty, Digital Security Controls shall, at its option, repair or

replace the defective equipment upon return of the equipment to its repair depot. This warranty

applies only to defects in parts and workmanship and not to damage incurred in shipping or

13

PGP922 Glass Break Detector Installation Guide

D-308652 PGP922 Rev.0

Содержание PGP922

















Отзывы: