Johnson Controls PG8932 страница 2 Скачать руководство пользователя

Страница: 2 / 29

Tamper

Removing the detector from the mounting plate initiates a tamper transmission. The tamper
condition is restored after the detector is mounted on the plate.

Battery

The wireless heat alarm is powered by a CR123A or DL123A battery. The detector
periodically checks for a low battery. If a low battery is detected, the detector sends a
message to the control panel, which indicates which detector has a battery. In addition, the
yellow LED of the detector flashes every 12 seconds. The detector's sounder chirps every
48 seconds and the yellow LED continues to flash until the battery is replaced. Pressing the
test/hush button silences the chirps for twelve hours if no other trouble conditions exist. The
battery should be replaced with a new battery when the chirps begin. At low battery, the test
button is disabled.

NOTE:

If the alarm does not sound, contact the installer or dealer for service.

Battery Installation and replacement

CAUTION: Risk of explosion if the battery is replaced with an incorrect type. Dispose of
the used battery according to the manufacturer's instructions.
A:

Battery compartment

To replace the battery, complete the following steps:

Twist the detector counterclockwise to remove the detector from its mounting base. To
remove the battery, carefully lift it from the + end using a flathead screwdriver.
Dispose of the battery according to local regulations.

To ensure a proper power-down sequence, wait a minimum of 30 seconds before
installing the new battery.

Insert a new CR123A or DL123A battery, available from a local Panasonic or Duracell
dealer, in the battery compartment (A). Insert the

–

end of the battery first. If the battery

is incorrectly inserted, carefully remove and correctly re-insert it following the
procedure described in step 1.

To re-install the detector on its mounting base, turn
the detector clockwise until the mating marks align.

After the power-up sequence, the green LED blinks
twice every 12 seconds to indicate normal operation.
If the battery is not installed correctly, the detector will
not operate, and the battery may be damaged. If the
detector does not power up, check that the battery is
installed correctly and fully charged.

Test the detector as described in this document.

CAUTION:

CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH

HUMIDITY MAY REDUCE BATTERY LIFE.

Installation instructions

Select an accessible location that is not prone to tampering or accidental damage. The heat
detector must be installed and maintained in accordance with the National Fire Protection

Association’s Standards (NFPA 72), the National Electrical Code and all local fire a

electrical  requirements.  The  mounting  surface  should  be  relatively  flat  and  capable  of
accepting  screws  or  anchors.  The  detector  is  to  be  installed  in  an  indoor  dry  location.
Exposure to weather or corrosive conditions may damage the unit. These detectors are not
to be used with detector guards.
Do NOT Install Detectors in the Following Areas:
In  or  near  areas  where  particles  of  combustion  are  normally  present  such  as  kitchens;  in
garages;  near  furnaces,  hot  water  heaters,  or  gas  space
heaters.  In  very  cold  or  very  hot  areas.  In  wet  or
excessively  humid  areas,  or  next  to  bathrooms  with
showers. In dusty, dirty, or insect-infested areas. Near
fresh air inlets or returns or excessively drafty areas.
Consult  NFPA  72,  the  local  Authority  Having
Jurisdiction  (AHJ),  and/or  applicable  codes  for  specific
information  regarding  the  spacing  and  placement  of
detectors.
The  PG8932/PG9932  wireless  heat  detector  shall  be
installed and used within an environment that provides the
pollution  degree  max  2  and  over  voltages  category  II  in
non-hazardous locations, indoor only. The equipment is
designed to be installed by SERVICE PERSONS only;
(SERVICE PERSON is defined as a person having the
appropriate  technical  training  and  experience
necessary to be aware of hazards to which that person
may be exposed in performing a  task and of measures
to minimize the risks to that person or other  persons).