Johnson Controls PENN VFD68 Скачать руководство пользователя страница 32

Страница: 32 / 32

Published in U.S.A.

www.johnsoncontrols.com

VFD68 Variable Frequency Drives (575 VAC)

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

® Johnson Controls and PENN are registered trademarks of Johnson Controls in the

United States of America and/or other countries. All other trademarks used herein are the property

Building Technologies & Solutions

507 E. Michigan Street, Milwaukee, WI

Technical Specifications

VFD68Dxx Variable Frequency Drive (575 VAC)

Input Power Voltage/Frequency

575 VAC, 50 Hz;
Continuous Duty

Output Voltage/Frequency

575 VAC, 50 Hz;
Continuous Duty

Input Devices

Johnson Controls/PENN® P499 Electronic Pressure Transducers

PWM Carrier Frequency

Adjustable 0.7 to 15 kHz

Motor Requirements

Three-phase NEMA Design B motors required; Inverter-rated motors recommended

Overload Capacity

150% of ampere rating for 1 minute

Start/Stop

Use STF input to start or stop the motor

Ambient Conditions

Storage:

-40 to 65ºC (-40 to 149ºF), 0 to 95% RH Non-condensing

Operating:

-40 to 50ºC (-40 to 122ºF), 0 to 95% RH Non-condensing

Altitude:

1,000 m (3,300 ft) Maximum without derating

Enclosures

UL Type 1 (NEMA) Fan Cooled

Maximum High Voltage Wire
Length

Up to 100 m (328 ft) between the VFD68 Drive and the motor (using the appropriate wire
gauge)

Compliance

North America:

cULus Listed, UL 508C, CSA-C22.2 No. 14, File E244421;

Dimensions (H x W x D)

Minimum:

150 x 140 x 136 mm (5-15/16 x 5-1/2 x 5-5/16 in.)

Maximum:

150 x 220 x 148 mm (5-15/16 x 8-11/16 x 5-13/16 in.)

Shipping Weight

575 VAC +5/-10% Production Models:

VFD68DFM

: 1.8 kg (3.96 lb)

VFD68DGM, VFD68DHM

: 2.0 kg (4.41 lb)

VFD68DJN, VFD68DKN, VFD68DLN

: 3.8 kg (8.38 lb)

Содержание PENN VFD68

































Результаты поиска

Содержание PENN VFD68

Отзывы:

Похожие инструкции для PENN VFD68

Бренды по названию

Популярные бренды

Johnson Controls PENN VFD68, Руководство по установке

Результаты поиска

Содержание PENN VFD68

Отзывы:

Похожие инструкции для PENN VFD68

Бренды по названию

Популярные бренды