manualshive.com logo in svg

Johnson Controls NS Series, Руководство по установке, Страница: 6 / 10

Поделиться
Скачать
Johnson Controls NS Series Скачать руководство пользователя страница 6

Part No. 24-11256-00007, Rev. —

6

NS8000 Series

Setup and adjustments

Adjusting the temperature setpoint

1.  To view the current setpoint value, press the 

Up

 or 

Down 

icon once.

2.  To increase or decrease the temperature setpoint by 0.5 degrees Fahrenheit or Celsius, press the 

Up

 or 

Down 

icon again.

3.  To save the new settings, press the 

Menu 

icon once to return to the home screen or wait for ten seconds for the screen to 

return to the home screen automatically.

4. 

Optional: 

Press and hold the 

Up

 or 

Down

 icon to continuously increase or decrease the temperature setpoint.

Adjusting the fan speed

1.  To view the current fan speed, press the 

Fan

 icon once.

2.  To adjust the fan speed, continue to press the 

Fan

 icon to cycle through the automtic, off, low, medium or

high fan speed settings.

3.  To save the new settings, press the 

Menu 

icon once to return to the home screen or wait for ten seconds for the screen to 

return to the home screen automatically.

Viewing the SA bus sensor address and the firmware version

1.  Press the 

Menu

 icon once to view the SA bus sensor address. See Table 2 for setting the SA bus sensor address

2.  Press the 

Menu

 icon a second time to view the firmware version.

3.  Press the 

Menu

 icon a third time to return to the home screen or wait for ten seconds for the screen to return to the

home screen automatically.

Adjusting the temperature unit

To change the temperature units from Fahrenheit to Celsius or Celsius to Fahrenheit, complete the following steps:

1.  On the home screen, press and hold the 

Up

 and 

Down

 icons for five seconds until the middle display disappears and the 

Celsius and Fahrenheit indicator icons blink.

2.  To toggle between Fahrenheit and Celsius, press the 

Up

 or 

Down

 icon.

3.  To save the new settings, press the 

Menu 

icon six times to return to the home screen or wait for ten seconds for the screen to 

return to the home screen automatically.

Changing the home screen default value

Choose whether you want to display current temperature or the setpoint value in the middle of the home screen. To change which 

value displays in the middle of the home screen, complete the following steps:

1.  Press and hold the 

Up

 and 

Down

 icons for five seconds until the Fahrenheit and Celsius indicator icons start to blink. All icons 

are visible on the display.      

2.  Press the 

Menu

 icon once.

3.  To select and switch between current temperature or setpoint value, press the 

Up

 or 

Down

 icon.

4.  To save the new settings, press the 

Menu 

icon five times to return to the home screen or wait for ten seconds for the screen to 

return to the home screen automatically.

Selecting the setpoint display value

To change whether current or setpoint temperature displays in the upper-right corner, complete the following steps:

1.  Press and hold the 

Up

 and 

Down

 icons for five seconds until the Fahrenheit and Celsius indicator icons start to blink.

2.  Press the 

Menu 

icon twice.

3.  To select and switch between current temperature or setpoint value, press the 

Up

 or 

Down

 icon.

4.  To save the new settings, press the 

Menu 

icon four times to return to the home screen or wait for ten seconds for the screen to 

return to the home screen automatically.

Selecting the maximum fan speed settings

The fan speed is set to high speed by default. To change the value of the maximum fan speed that displays on the home screen, 

complete the following steps:

1.  Press and hold the 

Up

 and 

Down

 icons for five seconds until the Fahrenheit and Celsius indicator icons start to blink.

2.  Press the 

Menu 

icon three times.

3.  To increase or decrease the maximum fan speed, press the 

Up

 or 

Down

 icon.

4.  To save the new settings, press the 

Menu 

icon three times to return to the home screen or wait for ten seconds for the screen 

to return to the home screen automatically.

Changing the decimal separator

1.  Press and hold the 

Up

 and 

Down

 icons for five seconds until the Fahrenheit and Celsius indicator icons start to blink.

2.  Press the 

Menu 

icon four times.

3.  To switch between decimal point or decimal comma, press the 

Up

 or 

Down

 icon.

4.  To save the new settings, press the 

Menu 

icon twice to return to the home screen or wait for ten seconds for the screen to 

return to the home screen automatically.

Notes: 

• 

To activate the home screen when the backlight is off, touch the screen to turn the backlight back on for ten seconds.

• 

All icons are visible on the home screen during configuration.

Содержание NS Series











Отзывы:

Нет отзывов