Johnson Controls NAE-S Скачать руководство пользователя страница 9

Ordering Information

Table 6: NAE-S Ordering Information

Product Code Number

Description

MS-NAE551S-2

Includes one RS-232C serial port, two RS-485 ports (FC-A and FC-B), one Ethernet port,

and one MS-BAT1010-0 Data Protection Battery. Supports two N2 or two BACnet MS/

TP (RS-485) trunks (or one N2 trunk and one BACnet MS/TP trunk). Supports up to 100

devices on each trunk. Requires a 24 VAC power supply.

MS-NAE551S-702

Replacement for a non-functional NAE551S-2.

Table 7: Accessories Ordering Information

Product Code Number

Description

MS-NAESCBL-0

Commissioning cable and non-metallic reset probe.

PAN-PWRSP

96 VA 120/24 VAC Power Assembly (Transformer, receptacle, 5 A, overcurrent circuit

breaker)

DRP-24V48W1AZ (Rev04)

CliQ DIN Rail 24 VDC Power Supply with connecting cable, manufactured by DeltaPSU,

power supply unit of Delta

®

 Electronics Group

MS-BAT1010-0

Replacement data protection battery for NAE-S. Rechargeable gel cell battery with a

typical life of 3 to 5 years at 70°F (21°C).

Technical Specifications

Table 8: NAE551S-2 Technical Specifications

Product Code Number

MS-NAE551S-2

Note: 

The NAE-S comes from the factory with 

Metasys

 Release 8.0 firmware, but you

may field-upgrade the engine to Release 10.1.

Power Requirements

MS-NAE551S-2 Engine:

Dedicated nominal 24 VAC, Class 2 power supply (North America) at 50/60 Hz (20 VAC

minimum to 30 VAC maximum)

DeltaPSU Power Supply for Internal Module with Embedded Encryption Technology:

Input: Dedicated nominal 100–240 VAC, Class 1 power supply (North America), at 50/60

Hz (85 VAC minimum to 264 VAC maximum)
Output: 24 VDC (22 VDC minimum to 26 VDC maximum)

Power Consumption

50 VA maximum

Power Specifications for

Encryption Board

Dedicated nominal 24 VDC, input voltage range 85–264 VAC (120–375 VDC), output

current 2.0A

Ambient Operating

Conditions

32 to 122°F (0 to 50°C); 10 to 90% RH, 86°F (30°C) maximum dew point

Ambient Storage Conditions -40 to 158°F (-40 to 70°C); 5 to 95% RH, 86°F (30°C) maximum dew point

Data Protection Battery

Supports data protection on power failure. Rechargeable gel cell battery: 12 V, 1.2 Ah,

with a typical life of 3 to 5 years at 70°F (21°C); Product Code Number: MS-BAT1010-0

Clock Battery

Maintains real-time clock through a power failure. Onboard cell; typical life 10 years at

70°F (21°C)

Processor

1.6 GHz Intel

®

 Atom

®

 processor

Memory

4 GB flash nonvolatile memory for operating system, configuration data, and operations

data storage and backup
1 GB SDRAM for operations data dynamic memory for all models

Network and Serial

Interfaces

One Ethernet port; 10/100/1000 Mbps; 8-pin RJ-45 connector (Use Cat5 or Cat6 cable)
Two optically isolated RS-485 ports; 9600, 19.2k, 38.4k, or 76.8k baud; pluggable and

keyed 4 position terminal blocks (RS-485 terminal blocks available)

NAE-S Installation Guide

9

Содержание NAE-S











Отзывы: