background image

 

4    

MS4PMUHVT Multi-Stage Electronic Temperature Control with Relay Pack Product/Technical Bulletin 

Mounting 

The MS4PMUHVT control is not position-sensitive 
but should be mounted for convenient wiring and 
adjustment. The MS4PMUHVT control may be 
mounted as a single unit or the control module and 
relay pack may be separated and mounted 
individually. 

Mounting the MS4PMUHVT Control as a 
Single Unit 

Before mounting the relay pack, ensure that there is 
sufficient space. Follow these steps to mount the 
relay pack: 

1.  Hold the MS4PMUHVT control against the 

surface and use it as a template to trace the 
mounting slots. 

2.  Drill holes for mounting screws in the holes 

indicated. 

3.  Use three screws (No. 8 or No. 10 size) to 

mount the MS4PMUHVT control. 

Mounting the Control Module and Relay Pack 
Separately 

Mount the relay pack and the control module within 
18 in. (46 cm) of each other. 

Removing the Control Module from the 
Relay Pack 

Follow these steps to separate the control module 
and the relay pack. See Figures 6-7. 

1.  Locate the mounting clip that holds the control 

module to the mounting bracket on the relay 
pack. 

2.  Squeeze the forward portion of the mounting clip 

together and slide the mounting clip back to 
remove the mounting clip from the back of the 
control module. 

3.  Pull the control module out of the mounting 

bracket on the relay pack. 

4.  Disconnect the wiring from the control module 

and the relay pack terminals V1, V2, O1, and 
O2. See Figures 7-9. 

Mounting the Relay Pack 

Before mounting the relay pack, ensure that there is 
sufficient space. Follow these steps to mount the 
relay pack: 

1.  Hold the relay pack with mounting bracket 

against the surface and use as a template to 
trace the mounting slots. 

 

2.  Drill holes for mounting screws in the slots indicated. 

3.  Use three screws (No. 8 or No. 10 size) to mount the 

relay pack. 

Mounting the Control Module 

Before mounting the control module, ensure that there is 
sufficient free space [at least 2-3/4 inches (70 mm)] 
behind the mounting surface. Follow these steps to 
mount the control module: 

1.  Cut a hole 1-3/16 x 2-13/16 inches (29 x 71 mm). 

2.  Remove the mounting clip from the control module. 

3.  Insert the control module into the hole. 

4.  Install the retaining clip and slide forward to adjust 

for tightness. 

5.  Reconnect the wires on the terminals in the relay 

pack to the corresponding terminals on the control 
module. See Figures 7-9. 

Mounting 

Clip

Control
Module

 

Figure 6: Removing the Mounting Clip and 

Control Module 

V

2

V

1

O1 O2

D

4

D

3

 

Figure 7: Relay Pack Terminal Positions on the 

Circuit Board 

Содержание MS4PMUHVT

















Отзывы: