manualshive.com logo in svg

Johnson Controls Metasys NCE25 series, Руководство по установке, Страница: 36 / 38

Поделиться
Скачать
Johnson Controls Metasys NCE25 series Скачать руководство пользователя страница 36

Table 19: NCE25

Operating System

Microsoft

®

 Windows Embedded CE 6.0 (Release 9.0)

Buildroot 2017.08.2 with Linux kernel 14.4 (Release 9.0.7)

Note: 

The Windows Embedded OS sticker on the bottom of the

network engine permits downgrading the engine to an older

Metasys

 release that uses a Windows Embedded OS.

Network and Serial

Interfaces
(Depending on the NCE

model.)

• One Ethernet port; 10/100 Mbps; 8-pin RJ-45 connector
• One optically isolated RS-485 SA Bus port; with a pluggable and

keyed 4-position terminal block (on all NCE25 models)

• One optically isolated RS-485 port; with a pluggable and keyed 4-

position terminal block (only on NCE25 models that support an N2

Bus or MS/TP bus trunk)

• One LonWorks port; FTT10 78 Kbps; pluggable, keyed 3-position

terminal block (only on NCE25 models that support a LonWorks

Network trunk). The LonWorks models are supported to run the

Metasys

 Release 9.0 software, 

but not the Release 9.0.7 update.

• One RS-232-C serial port with a standard 9-pin sub-D connector that

supports standard baud rates

• One USB serial port with a standard USB connector that supports

an optional, user-supplied external modem. Modem functions are

available with 

Metasys

 Release 9.0, but 

are not

 available after the

NCE is updated with Release 9.0.7.

• Option: One telephone port for the internal modem; up to 56 Kbps;

6-pin modular connector (NCE models with an optional internal

modem have one RS-232-C serial port only; not supported for an

engine with Release 9.0.7).

Analog Input/Analog

Output Point Resolution

• Analog Input Points: 16-bit resolution
• Analog Output Points: 16-bit resolution and ±200 mV accuracy on

0-10 VDC applications

Input/Output

Capabilities

• 10-Universal Inputs: Defined as 0–10 VDC, 4–20 mA, 0–600k ohm, or

Binary Dry Contact

• 8-Binary Inputs: Defined as Dry Contact Maintained or Pulse/

Accumulator Mode

• 4-Analog Outputs: Defined as 0–10 VDC or 4–20 mA
• 7-Binary Outputs: Defined as 24 VAC Triac (selectable internal or

external source power)

• 4-Configurable Outputs: Defined as 0–10 VDC or 24 VAC Triac BO

Dimensions
(Height x Width x Depth)

155 mm x 270 mm x 64 mm (6.1 in. x 10.6 in. x 2.5 in.), minimum

mounting space required: 250 mm x 370 mm x 110 mm (9.8 in. x 14.6

in. x 4.3 in.)

Housing

Plastic housing
Plastic material: ABS and polycarbonate
Protection: IP20 (IEC60529)

Mounting

On a flat surface with screws, on three mounting clips, or a single 35

mm DIN rail

NCE25 Installation Instructions

36

Содержание Metasys NCE25 series







































Отзывы:

Нет отзывов