manualshive.com logo in svg

Johnson Controls Metasys NCE25 series, Руководство по установке, Страница: 32 / 38

Поделиться
Скачать
Johnson Controls Metasys NCE25 series Скачать руководство пользователя страница 32

Table 15: LED designations, normal status, and descriptions

LED designation

Normal status

Descriptions/other conditions

ETHERNET (Green)

Flicker

Flicker = Data is transferring on the Ethernet

connection. Ethernet traffic is general traffic (may

not be traffic to or from the network engine).
Off Steady = No Ethernet traffic, probably indicates a

dead Ethernet network or bad Ethernet connection.

10 LINK (Green)

On steady (10 Mbps

network)

On Steady = Ethernet connection is established at 10

Mbps.

100 LINK (Green)

On steady (100

Mbps network)

On Steady = Ethernet connection is established at

100 Mbps.

RUN (Green)

On steady

On Steady = NCE software is running.
On 1 second, Off 1 second = NCE or NIE software is

in startup mode.
On 0.5 seconds, Off 0.5 seconds = NCE or NIE

software is shutting down.
Off Steady = Operating system is shutting down or

software is not running.

PEER COM (Green)

Varies

Flicker = Data traffic between network engines.

For an NCE or NIE that is not a Site Director, this

LED indicates regular heartbeat communications

with the Site Director. For a single NCE or NIE on a

network without an ADS, there is no flicker.

Accessories

Table 16: NCE25 Accessories Ordering Information

Product Code Number Description

MS-BAT1020-0

Replacement data protection battery for the NCE25. Rechargeable

NiMH battery: 3.6 V 500 mAh, with a typical life of five to seven years at

21°C (70°F).

TL-MAP1810-xx

Pocket-sized web server that provides a wireless mobile user interface

to 

Metasys

 field controllers, thermostats, and smart rooftop units. Refer

to the 

Mobile Access Portal Gateway Catalog Page (LIT-1900869)

 to identify

the appropriate product for your region.

MS-DIS1710-0

Local Controller Display connects to NCE on SA Bus and provides menu

display and navigation keypad for monitoring status and controlling

parameters on the NCE’s integral field controller.

Note: 

A DIS1710 display does not operate on NCE models that

have an integral controller display.

AS-XFR100-1

Power transformer (Class 2, 24 VAC, 92 VA maximum output), with

enclosure.

AS-XFR010-1

Power transformer (Class 2, 24 VAC, 92 VA maximum output), no

enclosure.

NCE25 Installation Instructions

32

Содержание Metasys NCE25 series







































Отзывы:

Нет отзывов