Johnson Controls Metasys NCE25 series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 38

Johnson Controls Metasys NCE25 series Скачать руководство пользователя страница 2

• Mount the NCE in a horizontal, upright orientation.
• Mount the NCE on an even surface in wall mount applications whenever possible. If you must

mount the network engine on an uneven surface, be careful not to crack the mounting clips or

network engine housing when tightening the screws. Use shims or washers to mount the NCE

evenly on the mounting surface.

• Mount the NCE in areas free of corrosive vapors, and observe the environmental limitations

listed in the

Technical specifications

section.

• Allow sufficient space to accommodate cable and wire connections. See Figure 1.
• Do not mount the network engine where the ambient temperature may exceed 50°C (122°F).
• Do not mount the network engine on surfaces that are prone to vibration or in areas where

electromagnetic or radio frequency emissions can interfere with network engine communication.

• Do not obstruct the network engine housing ventilation holes.
• Do not mount a power transformer below the network engine.
On applications where the network engine is mounted inside a panel or enclosure, follow these

additional guidelines:
• Do not install the network engine in an airtight enclosure.
• Do not install heat-generating devices in the enclosure with the network engine that may cause

the ambient temperature to exceed 50°C (122°F).

Wall mount applications

Use the holes in the three mounting clips for wall mount applications.
To mount the network engine on a wall or other vertical surface, complete the following steps:

1. Ensure that all three mounting clips are inserted into the back of the network engine housing

and then pulled outward and snapped firmly into the extended position. See Figure 2.

2. Mark the location of the three wall mount holes using the dimensions in Figure 1, or hold the

network engine up to the wall as a template and mark the locations.

3. Drill holes in the wall at the locations marked in Step 2 and insert wall anchors, if necessary.

NCE25 Installation Instructions

2

«
1
2
3
4
...
»

Содержание Metasys NCE25 series







































Отзывы:

Нет отзывов