Johnson Controls Metasys NCE25 series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 38

Johnson Controls Metasys NCE25 series Скачать руководство пользователя страница 1

NCE25 Installation Instructions

Application

The

Metasys

®

Network Control Engine (NCE) 25 Series controllers combine the network supervisor

capabilities and Internet IP network connectivity of a

Metasys

Network Automation Engine (NAE)

with the I/O point connectivity and direct digital control capabilities of a

Metasys

Field Equipment

Controller (FEC). These network engines provide a cost-effective solution designed for central plant

applications and large built-up air handlers.
NCE25 Series controllers provide integration to the following network protocols: BACnet/IP, BACnet

MS/TP, and N2 Bus and integrations to other building management communication technologies,

including Modbus

®

, M-Bus, and KNX. The network engine at 9.0.7 is shipped with the licenses and

drivers for all three communication protocols: Modbus, M-Bus, and KNX.

Note:

LonWorks

®

is no longer supported for an NCE at Release 9.0.7. All NCEs that feature the

LonWorks integration remain at Release 9.0 or earlier.

Figure 3 shows the physical features of an MS-NCE2567-0 model. See Table 18 for NCE25 Series

model information and features.

Important:

For existing custom integrations, contact your local Systems Integration Services

(SIS) team before an upgrade. Updated drivers can be provided on request.

Installation

Follow these guidelines when installing an NCE:
• Transport the NCE in the original container to minimize vibration and shock damage to the

network .

• Verify that all the parts shipped with the NCE.
• Do not drop the NCE or subject it to physical shock.

Parts included

• One NCE with removable terminal plugs.
• One data protection battery installed and connected when the NCE is shipped.
• One installation instructions sheet.

Materials and special tools needed

• Three fasteners appropriate for the mounting surface (M4 screws [#8] screws).
• One 20 cm (8 in.) or longer piece of 35 mm DIN rail, and appropriate hardware for mounting the

DIN rail.

Mounting

Location considerations

Follow these guidelines when mounting a network engine:
• Ensure that the mounting surface can support the NCE and any user-supplied panel or enclosure.

Part No. 24-10143-63 Rev. S
2018-12-17
Release 9.0.7

(barcode for factory use only)

*241014363S*

1
2
3
...
»

Содержание Metasys NCE25 series







































Отзывы:

Нет отзывов