Johnson Controls M9106 Series Скачать руководство пользователя страница 5

Страница: 5 / 8

M9106-xGx-2 Series Electric Non-Spring Return Actuators Installation Instructions

Wiring

CAUTION: Risk of Property Damage.

Do not apply power to the system before checking
all wiring connections. Short circuited or improperly
connected wires may result in permanent damage to
the equipment.

MISE EN GARDE: Risque de dégâts matériels.

Ne pas mettre le système sous tension avant d'avoir
vérifié tous les raccords de câblage. Des fils formant
un court-circuit ou connectés de façon incorrecte
risquent d'endommager irrémédiablement
l'équipement.

IMPORTANT:

Make all wiring connections in

accordance with the National Electrical Code and all
local regulations.

The actuator requires a 24 VAC control signal and is
compatible with a variety of controllers. (See
Figure 10.)

Proportional Control

Models: GGx

On-Off Control

Models: IGx

0-10 VDC

0-10 VDC
0-20 mA

VDC/mA

+24

COM

24 VAC

Auxiliary Switches

Models: All xGC

Feedback Potentiometer

Model: AGF (0-10,000 ohms)

NC1

NO1

10°

NC2

NO2

80°

Floating Control

Models: AGx and IGx

CCW

COM

24 VAC

100%

CCW

Wiper

Figure 10: Wiring for M9106 Models

Note:

To avoid excessive wear or drive time on the

motor for the AGx models, use a controller and/or
software that provides a time-out function to remove
the signal at the end of rotation (stall). The GGx and
IGx models have an auto shutoff to avoid excessive
wear or drive time on the motor.

Through the Conduit Openings

Depending on the M9106 model selected, one or both
conduit openings are used.

1. Loosen the cover screw and remove the actuator

cover.

2. Push the plastic conduit plug out of the

conduit opening with fingertip. (See Figure 11.)

Cover

Screw

Cover

Gear

Release

Plugs

(Conduit Openings)

Figure 11: Location of the Conduit Openings

3. Use the Phillips No. 1 screwdriver to puncture a

hole through the center of the plastic conduit plug.
Reinsert the plug into the conduit opening.

Note:

For applications requiring metal conduit,

thread the conduit fitting into the conduit opening and
hand tighten.

4. Insert the cable wires through the plastic plug,

compression fitting, or conduit fitting, and connect
to the terminals using the appropriate wiring
diagram in Figure 10.

IMPORTANT:

Install all quick-connect

terminals in the same direction to prevent shorting.
(See Figure 12.)

Figure 12: Orientation of Terminals

Note:

If using optional pluggable terminal blocks

(M9000-105 or M9000-106), insert the cable wires
through the conduit opening, and then connect the
wires to the terminals.

Содержание M9106 Series









Результаты поиска

Содержание M9106 Series

Отзывы:

Johnson Controls M9106 Series, Руководство по установке, Страница: 5 / 8

Результаты поиска

Содержание M9106 Series

Отзывы: